This post is more than 5 years old
5 Posts
0
53561
CMOS Battery - New Socket Style
I work on desktop PCs in the Optiplex and Vostro series. Recently I was handed a Vostro 220 that needs a new
CR 2032 CMOS battery. The issue I have is that the motherboard uses a battery socket style I'm not familiar with.
Generally, what you see are sockets that feature a small metal clip that you can push to one side and the battery
pops right out. This new socket type, however, does not have the spring clip feature. Instead, the battery is held
in place by means of black plastic protrusions that are part of the molded socket itself. It actually looks like the
battery was never meant to be replaced. I've tried merely prying the battery out with all manner of plastic tools,
but each time I approach whatever I perceive to be the breaking point of either the tool or socket and I back off.
I've spent over an hour trying to get the thing out. The service manual shows the older style socket with the
spring clip.
What's the secret?
Thanks and regards,
Thomas
jackshack
6.4K Posts
0
December 18th, 2013 23:00
I'm assuming you are describing a holder that lies flat against the motherboard in a manner similar to the older holder that uses the spring clip at one edge of the plastic frame. The holder I'm thinking of has a ledge of plastic that hides a part of the battery on one side, and a sort of finger arrangement of plastic on the other. Did you try pushing the cell farther under the ledge of plastic so that the other side comes free of the fingers? This type of holder has the spring under the plastic ledge that forces the battery against the side of the holder having the fingers so the fingers keep the battery secure.
osprey4
4 Operator
4 Operator
•
34.2K Posts
0
December 18th, 2013 16:00
Hi Thomas,
Here's what is shown in the manual. There's a small tab that you must push to the side to release the battery.
KXKVI
5 Posts
0
December 18th, 2013 20:00
That's the old style battery socket with the retaining tab. These new sockets have no such tabs.
Dell should have updated the manual.
I managed to pry it out with a plastic spudger, but it required a lot of force. You shouldn't have
to come close to breaking something in order to fix it. There must be a better way.
Thomas
KXKVI
5 Posts
0
December 19th, 2013 10:00
Hi Jackshack. Thanks for the reply.
Yes, that is precisely the battery holder I'm speaking of. I didn't try pressing down on on end because I
was afraid of damaging the underlying spring contact. However, now that I know that it's designed to
be used that way, I'll give it a shot. I have another Vostro lying around that I can test this on.
Thanks much for the info!
Thomas
KXKVI
5 Posts
0
December 19th, 2013 11:00
Confirmed. If you look carefully at the photographs, there is a small slot near the lower
right-hand corner of each picture. If you get a small tool in that slot and push the coin cell
inward toward the ledge, it pops right out. That's much better than simply prying the
battery out, which is, judging by the arrows in the photographs, what they're telling you
to do.
I've also been working on Vostro 200s. Those sockets have fingers on both sides, and
there is no side-spring to hold the battery in. I find the best strategy to remove the battery
from those is to use two spudgers; one to hold the socket against the PC board, and the
other to pry the battery up in just the right spot.
I wonder why they felt the battery sockets needed a re-design. Personally, I've always
had good luck with the original style, and they are certainly the easiest to deal with.
Regards,
Thomas
jackshack
6.4K Posts
0
December 19th, 2013 13:00
I'm glad to have helped. The photo is a Dell graphic, and I never understood the idea of the arrows on the sides of the cell myself. I figure it is a new photo that was inserted into a figure that had the older battery holder originally.
Best of luck to you.