This post is more than 5 years old
22 Posts
0
128766
remote systems
how can I configure bios values on remote systems with Dell Client PowerShell Provider (http://en.community.dell.com/techcenter/enterprise-client/w/wiki/6901.dell-client-powershell-provider.aspx)?
karthikchandran89
49 Posts
0
May 23rd, 2014 06:00
Retok,
You can still install HAPI alone individually using the HAPI_X86_64.zipx file in the PowerShell Beta folder.
Steps are given in Readme.txt as well.
Please follow the steps below to install HAPI driver
- Unzip the HAPI_X86(*).zipx (32/64 bit Arch) file into your working folder.
- Open a Command Prompt with administrative rights and navigate to your working folder.
- Execute HAPIInstall.bat from the HAPI folder. This should install HAPI driver.
- Execute "Driverquery /v" on the same command prompt and verify if "dcdbas" is visible from the
list.
- If dcdbas is visible, then Driver installation is successful.
please share us your feedback.
Also OMCI is fixing all the Monitor related issue in coming release.
DELL-Warren B
1.1K Posts
1
May 21st, 2014 13:00
You would need to install the HAPI driver and PowerShell Provider on the remote systems. Then either run a powershell script that leverages the provider, or invoke a remote powershell session to the remote system and execute the commands that way.
retok
22 Posts
0
May 22nd, 2014 01:00
retok
22 Posts
0
May 22nd, 2014 01:00
karthikchandran89
49 Posts
1
May 22nd, 2014 05:00
Retok,
Thanks for your details .
Can You please go to the Properties of the .DLL file by right clicking on it.and check for the any messages saying to Unblock it.
Also please share the information about PS version on both the Systems.
DELL-Vibha G
38 Posts
1
May 22nd, 2014 06:00
Perform Security->Unblock for the downloaded zip file Dell_SMBIOS_Provider.zip to unblock all assemblies at once.
Please share the outcome with us.
karthikchandran89
49 Posts
0
May 22nd, 2014 08:00
Reto ,
this error says that there is no drive created when u import the module.
please do a "gdr" in PS prompt and check if there is a drive named DellSMbios.
Also please share us the System model, OMCI, PowerShell and OS versions which your using.
retok
22 Posts
0
May 22nd, 2014 08:00
DELL-Vibha G
38 Posts
0
May 23rd, 2014 00:00
Execute "remove-module DellBIOSProvider" prior to imorting the module again with unblocked assemblies.
You can add -verbose switch for extra messages.
retok
22 Posts
0
May 23rd, 2014 04:00
retok
22 Posts
0
May 23rd, 2014 05:00
karthikchandran89
49 Posts
0
May 23rd, 2014 05:00
Retok,
This is a very earlier version of OMCI ( Hapi too). please upgrade to OMCI 8.2.1 from this below link.
http://en.community.dell.com/techcenter/systems-management/w/wiki/1773.openmanage-client-instrumentation-omci.aspx
i would suggest you to disconnect the Remote session and connect back after upgrade of OMCI.
this will solve all your issues. :)
retok
22 Posts
0
May 23rd, 2014 06:00
karthikchandran89
49 Posts
1
May 23rd, 2014 06:00
Welcome Reto,
OMCI Version will soon be available. please do write to us about any queries on OMCI and Dell PS. !
Thanks
Karthik.C