This post is more than 5 years old
5 Posts
0
8950
Clariion CX600
I need to configure an EMC CLARiiON CX600, but I have no software anyone can tell me how to get it?
and I have the product registered in the powerlink website, what should I do?
This post is more than 5 years old
5 Posts
0
8950
I need to configure an EMC CLARiiON CX600, but I have no software anyone can tell me how to get it?
and I have the product registered in the powerlink website, what should I do?
Top
RRR
2 Intern
2 Intern
•
5.7K Posts
0
November 5th, 2010 04:00
emc60740 discribes the CX600:
Failing Device: BIOS ROM
FRU: STORAGE PROCESSOR
Description: Data Directory Boot Service Failed Error!
Number of Sectors = 0x01
LBA: 0x00000000
Failing Device: BIOS ROM
FRU: STORAGE PROCESSOR
Description: Disk not logged in Error!
Target ID: 0x00
OR
If one SP boots properly but the other gets the above message in HyperTerminal, replace the cabling from the SP to the DAE-OS. If it still fails, try the LCC card on the DAE-OS.
Note: Wait long enough for the problem SP to boot as it can take as long as an hour to come up.
Hope this helps.
So if you did everything as described, I'm affraid you'll have to order your first 5 drives to be reimaged or get these drives elsewhere.
RRR
2 Intern
2 Intern
•
5.7K Posts
0
November 2nd, 2010 00:00
Do the first 5 drives still contain the FLARE operating system ?
So where do you stand now ?
JoelGav
5 Posts
0
November 3rd, 2010 08:00
I was doing several tests, I could not get cable db9, I hope to have tomorrow.
where I can download the Navisphere?
RRR
2 Intern
2 Intern
•
5.7K Posts
1
November 4th, 2010 04:00
Navisphere Manager runs on both storage processors, so you don't need to download / install this anywhere. Simply go to http:// of SPA or SPB> and that's it.
AlanZ1
790 Posts
0
November 4th, 2010 05:00
This discussion has been moved to the Unified Storage community where it should get a broader audience.
JoelGav
5 Posts
0
November 4th, 2010 10:00
when trying to connect to the RS232 port, displays the following error:
checking username and password...
Eror 721: remote computer did not respond
any idea what could be wrong?
I connect with hyperterminal and shows me this
El mensaje fue editado por: JoelGav
1 Attachment
sin serial imagen del error.png
RRR
2 Intern
2 Intern
•
5.7K Posts
0
November 5th, 2010 04:00
Check out Primus emc139286
During the boot process, the Data Directory Boot Service (DDBS) is unreadable and prevents access to the storage processor operating system image. This normally indicates a backend issue (drive, loop, cable, enclosure, etc.) and not a corrupted image. Under specific and rare circumstances, the DDBS image may have become corrupt due to a rebuild issue.
The following versions of FLARE have the potential for this DDBS partition not to rebuild properly:
If only one SP is in a 'rolling' reboot condition, DO NOT attempt to reboot the peer SP. See solution emc139469 for information on how to fix a single SP 'rolling' reboot condition.
If both SPs are in a 'rolling' reboot condition, contact CLARiiON TS2 for support. Engineering involvement will be required and a procedure provided at that time.
The following Release 22 code does not have the issue as described in solution emc139469:
Upgrade the array to FLARE Release 22 Patch .505 or Patch .506 to resolve the issue.
RRR
2 Intern
2 Intern
•
5.7K Posts
0
November 5th, 2010 04:00
So Hyperterminal over RS232 ? If you can see some boot sequence, at least the cable is ok.
Hmmmmm. an error like "Data Directory Boot Service Not Loaded Error!" doesn't sound good.
I wonder if this could be a msg from the hardware saying it's missing the Operating System. And if that's the case, you need to have the first 5 drives reimaged. Let me check if I can find anything on Primus.
JoelGav
5 Posts
0
November 5th, 2010 08:00
With your help I on the right track, I could determine which are the first 5 drives and put them right, the SP left me without any alarm.
The drive 9 shows me a alarm, not how important is this.
but still I can not do PPP connection, follow this guide I found to make the connection but does not work, https: / / community.emc.com/thread/109402 not know if it's because I am working from a windows xp virtual Windows 7 because since I could not find how to make the PPP connection for the serial cable
JoelGav
5 Posts
0
November 5th, 2010 09:00
I was able to solve the connectivity problem and begin configuration.
Thanks RRR.
RRR
2 Intern
2 Intern
•
5.7K Posts
0
November 11th, 2010 00:00
I'm glad it worked out for you !