Solved!
Go to SolutionA
Admin_Omicron
4 Posts
0
13889
April 4th, 2018 14:00
U2718Q, HDCP 2.2 support using DP?
I recently purchased a U2718Q A01 monitor, and have it connected via Displayport to a motherboard with HD 630 graphics. The Kaby Lake generation, which does support HDCP 2.2. However, according to the Cyberlink "UHD Ready" program, there is no HDCP 2.2 supported on it. I have the latest driver installed for the HD 630 graphics. I do get a successful message for older HDCP versions though. Did the A01 revision of this monitor do away with HDCP 2.2 support?
13445
0
Posted April 5th, 2018 07:00
According to the User's Guide page 12, all of the ports support HDCP 2.2. I doubt that we would "remove" this capability when moving from A0 to A01.
* Download this tool to your windows desktop
* Install the application
* Open the BD & 3D Assistant icon on the desktop. What does it state for HDCP?I would then move the monitor to a computer with a discrete Nvidia or AMD video card with mDP out port or DP out port. Then run the same test.
DELL-Chris M (old account)
#IWork4Dell
13435
0
Posted April 5th, 2018 08:00
If you can simply get 100% confirmation from the engineers behind the monitor that revision A01 is indeed HDCP 2.2 compatible on both the Displayport and HDMI interfaces (per the manual for A00,) then that is good enough for me. It may be that I need a more up to date copy of Windows 10 for HDCP 2.2 to be enabled via the Intel drivers.13437
0
Posted April 5th, 2018 08:00
The U2718Q is hardware bound to HDCP 2.2. My guess is that the low end onboard Intel HD 630 GPU is the fault. You can try to install the latest driver directly from Intel. But until you get another system in there that is using a discrete Nvidia or AMD video card, we cannot know 100% if the U2718Q is at fault or not.
DELL-Chris M (old account)
#IWork4Dell 13439
0
Posted April 5th, 2018 08:00
This software is painting an even worse picture, it is telling me that the connection is analog (like I was using an old VGA port or something.) The Cyberlink software at least told me I was some degree of HDCP compatible. Definitely nothing analog here, I am using the Displayport 1.2 connection from the HD 630 to the Displayport 1.2 on the monitor. It's running at 60hz at 4k (so definitely negotiated at 1.2.) I don't have access to any other computers with different interfaces or GPUs.13391
0
Posted April 6th, 2018 14:00
Firmware != hardware revision. The hardware revision is the A00/A01 and so forth. Does the A01 hardware revision support it?13355
0
Posted April 8th, 2018 13:00
The firmware installed denotes the hardware revision. But all support HDCP 2.2.
DELL-Chris M (old account)
#IWork4Dell 11942
0
Posted August 1st, 2018 07:00
I was able to make HDCP 2.2 work only after installing latest firmware M2B102. Using initial firmware DHCP was not working through DP, it was only working through HDMI. Spent 2 days trying to make it work, hope it helps someone. (FYI: Netflix does not work without HDCP, so basically it does not work on initial firmware)
DELL-Chris M
Community Manager
•
56891 Posts
•
232143 Points
13399
1
Posted April 6th, 2018 04:00
Their response, "Regardless of firmware version, all U2718Q video ports use HDCP 2.2."
DELL-Chris M (old account)
#IWork4Dell