UNSOLVED
E
evobe_taxi
4 Posts
0
3451
April 27th, 2016 15:00
Changing subnet errors
OK, I've been tasked with decreasing the size of my subnet on our management VLAN. Whenever I try to go from .240 to .248 I get..
Error! Subnet conflict between specified IP Address and current configuration. All routing interfaces, service ports and network ports must be configured on different subnets.
Not sure why this is happening, I'm the junior here so I admit I'm a little lost.
Here's my running config:
sntp unicast client enable
sntp server 10.101.2.246
clock summer-time recurring USA
clock timezone -5 minutes 0 zone "EST"
stack
member 1 2
member 2 2
exit
ip address 10.101.19.10 255.255.255.0
ip address vlan 7
ip domain-name blserviceinc.com
ip name-server 10.101.2.245
ip name-server 10.101.2.246
ip routing
ip route 0.0.0.0 0.0.0.0 10.101.1.1
ip route 10.105.0.0 255.255.0.0 10.101.1.13
ip route 172.24.0.0 255.255.240.0 10.101.1.5
ip route 10.102.0.0 255.255.0.0 10.101.1.13
ip helper-address 10.101.2.246 domain
interface vlan 1
routing
ip address 10.101.2.1 255.255.240.0
exit
interface vlan 2
name "VMotion"
exit
interface vlan 3
name "ATTInternet"
exit
interface vlan 4
name "Comcast Internet"
exit
interface vlan 6
name "Phone-Net"
exit
interface vlan 7
name "Management"
the only change is that Vmotion no longer exists and management vlan is now 10.101.19.1 with a /24 mask.
Any help would be appreciated.
Thanks
evobe_taxi
4 Posts
2453
0
Posted April 28th, 2016 11:00
Would that then fix the error I'm getting when I attempt to change vlan 1 to 255.255.248.0?
So, to be clear, vlan 7 is our management vlan, and that's currently vlan 7 with an ip of 10.101.19.1 with a mask of 255.255.255.0.
The vlan I'm interested in changing in vlan 1 which is 10.101.2.1 with a mask of 255.255.240.0. I'd like to change that to 255.255.248.0
Thanks for the reply.
evobe_taxi
4 Posts
2453
0
Posted April 28th, 2016 12:00
VLAN 1 already has an IP address:
interface vlan 1
routing
ip address 10.101.2.1 255.255.240.0
exit
I just want to change the subnet mask to 248 but whenever I attempt to do it I get;
Error! Subnet conflict between specified IP Address and current configuration. All routing interfaces, service ports and network ports must be configured on different subnets.
Which I don't get because I don't have another subnet with that mask, nor do I have any IP addresses in that range.
Much appreiciated.
DELL-Josh Cr
Community Manager
•
9752 Posts
•
44578 Points
2453
0
Posted April 28th, 2016 12:00
Oh ok, no, that would change VLAN 7. For VLAN 1 how are you changing it? Are you removing the existing IP with no ip address and then putting the new one on?
DELL-Josh Cr
Community Manager
•
9752 Posts
•
44578 Points
2453
0
Posted April 28th, 2016 13:00
.240 includes .248 so it sees the conflict there, you have to remove the existing IP first.
evobe_taxi
4 Posts
2453
0
Posted April 28th, 2016 14:00
Ok so to be clear, I'd have to remove the subnet 255.255.240.0 subnet mask completely, save it, then add 255.255.248.0?
Edit: I'm doing these changes in dell openmanage btw, so I'm not sure it'll let me clear out my subnet mask completely.
DELL-Josh Cr
Community Manager
•
9752 Posts
•
44578 Points
2453
0
Posted April 27th, 2016 17:00
Hi,
A .240(/28) has 16 hosts per subnet a .248(/29) subnet only has 6 hosts. A /24 is a subnet of 255.255.255.0 with 254 hosts
ip address 10.101.19.10 255.255.255.0
ip address vlan 7
change to this
ip address 10.101.19.1 255.255.255.248
ip address vlan 7