DELL EMC SCALEIO READY NODE 13G: R730 PROCESSOR REPLACEMENT PLEASE NOTE: THIS VIDEO IS MEANT TO SUPPLEMENT, BUT NOT REPLACE, A COMPLETE READING OF THE CURRENT FRU PROCEDURE, AS OBTAINED FROM THE DELL/EMC SOLVE DESKTOP APPLICATION. IF THERE IS ANY APPARENT CONTRADICTION BETWEEN THIS VIDEO AND THE FRU PROCEDURE, ALWAYS DEFER TO THE CURRENT FRU PROCEDURE.
FIRST STEP: EITHER YOU OR THE CUSTOMER LOG IN TO THE SCALEIO ADMINISTRATION SYSTEM USING AN ID WITH RIGHTS TO RUN WITH THE SCALEIO GUI DOUBLE-CLICK THE EMC SCALEIO GUI ENTER IP ADDR. OR NAME OF MASTER MDM. ENTER AN ADMINISTRATOR-LEVEL ID AND PASSWORD. ...AND YOU'RE IN. PROCEED TO THE NEXT STEP. FROM WITHIN THE SCALEIO GUI, CHOOSE THE BACKEND TAB. WITH THE VIEW SET TO "ALL SDSS"... EXPAND THE LIST AND FIND THE TARGET SDS.
RIGHT CLICK THE SDS AND SELECT ENTER MAINTENANCE MODE CLICK OK. WAIT FOR THE GREEN CHECKMARK. CLICK CLOSE. THE SDS ICON CHANGES TO INCLUDE AN ORANGE WRENCH. FOLLOW NORMAL PROCEDURES TO SAFELY SHUT DOWN THE SDS'S HOST AND PROCEED. LOG IN TO THE IDRAC USING ROOT ID OR ITS EQUIVALENT. CLICK BOTH "SYSTEM ID LED ON/OFF" AND POWER ON/OFF" CLICK "OK" TO EACH ACTION IDRAC DISPLAY REFRESHES... THE SYSTEM ID LED IS NOW FLASHING.
AT THIS POINT THE SYSTEM NEEDS TO BE GRACEFULLY SHUT DOWN DELL 13G R730 PROCESSOR REPLACEMENT LOCATE THE SYSTEM. SYSTEM SHOULD BE POWERED DOWN, WITH THE SYSTEM ID LED FLASHING. DOUBLE-CHECK THE SERIAL NUMBER. GENTLY SLIDE THE SYSTEM OUT. TAKE ESD PRECAUTIONS. REMOVE THE COVER. REMOVE THE COOLING SHROUD. LOOSEN ONE OF THE RETENTION SCREWS. HEAT SINK IS NECESSARY TO MAINTAIN PROPER THERMAL CONDITIONS.
NEVER REMOVE THE HEAT SINK UNLESS YOU INTEND TO REMOVE THE PROCESSOR. ALLOW APPROXIMATELY 30 SECONDS FOR THE HEAT SINK TO LOOSEN FROM THE PROCESSOR LOOSEN THE DIAGONALLY OPPOSITE RETENTION SCREW NEXT. REPEAT THE PROCEDURE TO REMOVE THE REMAINING TWO SCREWS. REMOVE THE HEAT SINK. RELEASE THE OPEN FIRST SOCKET-LEVER THEN RELEASE THE CLOSE FIRST SOCKET-LEVER. LIFT THE PROCESSOR SHIELD. LIFT THE PROCESSOR CAREFULLY. INSTALL THE NEW PROCESSOR. CLOSE THE PROCESSOR SHIELD.
LOCK THE CLOSE FIRST SOCKET-RELEASE LEVER. THEN LOCK THE OPEN FIRST SOCKET-RELEASE LEVER. APPLY THE THERMAL GREASE ON TOP OF THE PROCESSOR RE-INSTALL THE HEAT SINK TIGHTEN ONE OF THE RETENTION SCREWS THEN TIGHTEN THE DIAGONALLY OPPOSITE RETENTION SCREW REPEAT THE PROCEDURE TO TIGHTEN THE REMAINING TWO SCREWS RE-INSTALL THE COOLING SHROUD REPLACE THE COVER.
GENTLY SLIDE THE SYSTEM BACK IN. YOU MAY NEED TO HELP THE CABLE MANAGEMENT SYSTEM FOLD BACK IN. REPLACE THE BEZEL. GATHER YOUR EQUIPMENT, PARTS AND PAPERWORK. BACK TO IDRAC CONSOLE ACCESS. WITHIN THE IDRAC CONSOLE, CLICK "SYSTEM ID LED ON/OFF" TO TURN OFF THE FLASHING LED CLICK "OK." SYSTEM ID LED IS NOW OFF. POWER ON THE SYSTEM. CLICK "OK." SYSTEM IS NOW COMING UP. INDICATORS OF SDS STORAGE IN MAINTENANCE MODE.
GO TO THE BACKEND TAB. VIEW "BY SDSS" ORANGE WRENCH ON SDS ICON MEANS MAINTENANCE MODE. RIGHT-CLICK AND CHOOSE EXIT MAINTENANCE MODE. CONFIRM AND CLICK OK. GREEN CHECKMARK SHOWS THE OPERATION TO BE COMPLETE. CLICK CLOSE. SOME REBUILD ACTIVITY WILL OCCUR. THE SDS ICON HAS RETURNED TO NORMAL. THE DASHBOARD PANEL IS BACK TO NORMAL. DELL EMC
