Du må ikke slukke for din computer eller fjerne strømkablet, når BIOS'en opdateres, da det kan beskadige din computer. I forbindelse med opdateringen genstartes din computer, og der vises eventuelt kortvarigt en sort skærm.
Før du opdaterer, skal du læse installationsvejledningen og de vigtige oplysninger, der er angivet nedenfor.
Dell Precision M4800 System BIOS
Genstart er nødvendig Installeret Denne fil blev automatisk installeret som en del af en nylig opdatering. Hvis du oplever problemer, kan du downloade og geninstallere manuelt.Indholdet på denne side er muligvis blevet oversat automatisk. Udfyld formularen nederst på siden for at give feedback.
This package contains the Dell system BIOS update and is supported on Dell Precision M4800 that runs Windows and DOS operating systems. BIOS is a firmware that is embedded on a small memory chip on the computer's system board. It controls the keyboard, monitor, disk drives and other devices.
Anbefalet
Tjek kompatibilitet
Indtast produktoplysningerne for at få vist de seneste driveroplysninger for dit systemIndtast din Dell-servicekode eller -model
Vil du søge efter dit produkt? Indtast et produkt-id. Vis mig hvordan
Denne driver er ikke kompatibel
Denne driver er ikke relevant for det valgte produkt. Vælg et andet produkt for at indtaste dine produktoplysninger for denne driver igen, eller gå til siden Produktsupport for at se alle drivere til et andet produkt.
Log på Windows som administrator for at bruge automatisk scanning. Hvis du allerede er logget på som administrator og får vist denne meddelelse, skal du genstarte enheden. Dit system administreres af din it-administrator, og funktionaliteten kan være begrænset.
Find flere opdateringer. Brug SupportAssist til at finde alle de seneste driveropdateringer til din enhed.
Programrettelser og forbedringer
Fixes:
- Fixed the issue where system was not entering F2/F12 options on special configuration systems.
- Fixed SATA hot plug capability issue.
- Fixed a potential issue where system stops responding when an incorrectly formatted password is entered in the BIOS Security Manager (BIOS preboot password) screen.
- Updated CPU microcode to address security advisory Intel Security Advisory INTEL-SA-00115 (CVE-2018-3639 & CVE-2018-3640).
- Updated Intel ME Firmware to address security advisories INTEL-SA-00112 (CVE-2018-3628 CVE-2018-3629 CVE-2018-3632), INTEL-SA-00118(CVE-2018-3627) & INTEL-SA-00141 (CVE-2018-3616).
Enhancements:
- Updated Graphics Output Protocol driver which reflects the IntelGOpDrive.efi.
- Added BIOS Password Feature: Master Password Lockout.
Læs mere- Fixed the issue where system was not entering F2/F12 options on special configuration systems.
- Fixed SATA hot plug capability issue.
- Fixed a potential issue where system stops responding when an incorrectly formatted password is entered in the BIOS Security Manager (BIOS preboot password) screen.
- Updated CPU microcode to address security advisory Intel Security Advisory INTEL-SA-00115 (CVE-2018-3639 & CVE-2018-3640).
- Updated Intel ME Firmware to address security advisories INTEL-SA-00112 (CVE-2018-3628 CVE-2018-3629 CVE-2018-3632), INTEL-SA-00118(CVE-2018-3627) & INTEL-SA-00141 (CVE-2018-3616).
Enhancements:
- Updated Graphics Output Protocol driver which reflects the IntelGOpDrive.efi.
- Added BIOS Password Feature: Master Password Lockout.
Version
A25, A25
Udgivelsesdato
30 okt. 2018
Downloadtype
System-BIOS
Kategori
BIOS
Vigtighed
KritiskDell Technologies anbefaler på det kraftigste, at denne opdatering installeres så hurtigt som muligt. Opdateringen indeholder vigtige fejlrettelser og ændringer med henblik på at forbedre dit Dell-systems funktionalitet, pålidelighed og stabilitet. Den kan også omfatte sikkerhedsrettelser og andre funktionsforbedringer.
Tilgængelige formater
Filformat: CPG BIOS-eksekverbar fil til Windows/DOS
Filnavn: M4800A25.exe
Filstørrelse: 9.69 MB
Dette er en stor fil. Det kan tage et stykke tid at downloade den, afhængigt af din downloadhastighed.
Formatbeskrivelse:
Dette filformat består af en BIOS-eksekverbar fil. Universal-formatet (Windows/MS DOS) kan bruges til at installere fra ethvert Windows- eller MS DOS-miljø.
Kontrollér kontrolsumværdien for at sikre overførslens integritet.
MD5:
fb11c6dab58bf9a01969f8048e371c43
SHA1:
19d36c477f2965ffd0976728aade948fe7ce9330
SHA-256:
0c7aec697ffa4a796dd2174c18189a869af5e241a73bc8c12526a2eaa56ea8d3
Når du downloader filerne, accepterer du samtidig betingelserne i Dells softwarelicensaftale. (på engelsk)
Gælder for
Dell Precision M4800
Installationsvejledning
Updating the BIOS through Windows
1. Click Download File, to download the file.
2. When the File Download window is displayed, click Save to save the file to your hard drive.
3. Browse to the location where you downloaded the file and double-click the new file.
Windows System restarts automatically and update BIOS at the system startup screen.
After BIOS update is completed, system will reboot automatically to take effect.
Updating the BIOS from a DOS environment with Legacy boot mode (Non-Windows users)
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system and then Press F12 key and Select USB Storage Device and Boot to DOS prompt.
3. Run the file by typing copied file name where the executable file is located.
DOS System restarts automatically and update BIOS at system startup screen.
After BIOS update is completed, system will reboot automatically to take effect.
Updating the BIOS from a DOS environment with UEFI boot mode (Non-Windows users)
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system and then go to BIOS Setup by pressing F2 key and go to General > Boot Sequence > Boot > Boot List Option.
3. Change UEFI to Legacy of Boot List Option.
4. Go to Exit > Save Changes and reboot system.
5. Press F12 and then Select USB Storage Device and Boot to DOS prompt.
6. Run the file by typing copied file name where the executable file is located.
DOS System restarts automatically and update BIOS at system startup screen.
After the BIOS update is finished, system will reboot automatically.
7. Go to BIOS Setup by pressing F2 key and go to General > Boot Sequence > Boot > Boot List Option.
8. Change Legacy to UEFI Boot Option.
9. Go to Exit > Save Changes and reboot system.
Note 1: You must provide a bootable DOS USB drive. This executable file does not create the DOS system files.
Note 2: Ensure that you suspend BitLocker encryption before updating BIOS on a BitLocker-enabled system. If you do not enable BitLocker on your system, you can ignore this step.
1. Click Download File, to download the file.
2. When the File Download window is displayed, click Save to save the file to your hard drive.
3. Browse to the location where you downloaded the file and double-click the new file.
Windows System restarts automatically and update BIOS at the system startup screen.
After BIOS update is completed, system will reboot automatically to take effect.
Updating the BIOS from a DOS environment with Legacy boot mode (Non-Windows users)
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system and then Press F12 key and Select USB Storage Device and Boot to DOS prompt.
3. Run the file by typing copied file name where the executable file is located.
DOS System restarts automatically and update BIOS at system startup screen.
After BIOS update is completed, system will reboot automatically to take effect.
Updating the BIOS from a DOS environment with UEFI boot mode (Non-Windows users)
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system and then go to BIOS Setup by pressing F2 key and go to General > Boot Sequence > Boot > Boot List Option.
3. Change UEFI to Legacy of Boot List Option.
4. Go to Exit > Save Changes and reboot system.
5. Press F12 and then Select USB Storage Device and Boot to DOS prompt.
6. Run the file by typing copied file name where the executable file is located.
DOS System restarts automatically and update BIOS at system startup screen.
After the BIOS update is finished, system will reboot automatically.
7. Go to BIOS Setup by pressing F2 key and go to General > Boot Sequence > Boot > Boot List Option.
8. Change Legacy to UEFI Boot Option.
9. Go to Exit > Save Changes and reboot system.
Note 1: You must provide a bootable DOS USB drive. This executable file does not create the DOS system files.
Note 2: Ensure that you suspend BitLocker encryption before updating BIOS on a BitLocker-enabled system. If you do not enable BitLocker on your system, you can ignore this step.
Har du brug for hjælp med BIOS-problemer?
Find en løsning i Dells fejlfindingsvejledning for BIOSHjælp og selvstudier til drivere
Du kan finde flere downloads på Drivere og overførsler. Hvis du har brug for hjælp til at bruge oplysningerne på denne side, kan du besøge Hjælp og selvstudier til drivere.