American Megatrends (AMI) PERC 2/SC, PERC2/DC, v.4.21, A03
AUTOMATISK INSTALLERETDenne fil blev automatisk installeret som en del af en nylig opdatering. Hvis du oplever problemer, kan du downloade og geninstallere manuelt.
Indholdet på denne side er muligvis blevet oversat automatisk. Udfyld formularen nederst på siden for at give feedback.
Denne fil blev automatisk installeret som en del af en nylig opdatering. Hvis du oplever problemer, kan du downloade og geninstallere manuelt.
Dell PowerEdge RAID Controller 2/SC, 2/DC, 4/DC, 4/SC, 3/QC, 3/DC, 3/DCL, 3/SC, PERC 4/Di, and CERC ATA100/4CH, Device Driver for Windows NT 4.0.
Version: 4.21
Anbefalet
Find den bedste download til dit system
Indtast produktoplysningerne for at få vist de seneste driveroplysninger for dit system
Søg i support
Indtast din Dell-servicekode eller -model
Vil du søge efter dit produkt? Indtast et produkt-id.Vis mig hvordan
Søgningen gav ingen resultater.Vi kunne ikke finde nogen match til din søgning. Rediger din søgning, og prøv igen.
Denne driver er ikke kompatibel
Denne driver er ikke relevant for det valgte produkt. Vælg et andet produkt for at indtaste dine produktoplysninger for denne driver igen, eller gå til siden Produktsupport for at se alle drivere til et andet produkt.
Log på Windows som administrator for at bruge automatisk scanning. Hvis du allerede er logget på som administrator og får vist denne meddelelse, skal du genstarte enheden.Dit system administreres af din it-administrator, og funktionaliteten kan være begrænset.
Find flere opdateringer. Brug SupportAssist til at finde alle de seneste driveropdateringer til din enhed.
Programrettelser og forbedringer
Fixes or Enhancements in this Release
Enhancements:
1) None.
Fixes:
1) A fix was made in the Driver to initialize the data Structures for some of the IOCTL calls.
2) Driver no longer filters out all other commands except SCSI READ and SCSI WRITE
Dell Technologies anbefaler at gennemse denne opdatering for at afgøre, om den er relevant for dit system. Opdateringen indeholder ændringer, der kun har indflydelse på visse konfigurationer, eller tilvejebringer nye funktioner, der muligvis passer til dit miljø.
Dette er en stor fil. Det kan tage et stykke tid at downloade den, afhængigt af din downloadhastighed.
Formatbeskrivelse:
Dell Update Packages (DUP) i Microsoft Windows 32-bit-format er udviklet til at køre på Microsoft Windows 64-bit-operativsystemer. Dell Update Packages (DUP) i Microsoft Windows 64-bit-format kan kun køre på Microsoft Windows 64-bit-operativsystemer. Når du vælger en driveropdatering, skal du sørge for at vælge den udgave, der passer til dit operativsystem.
Dell PowerEdge RAID Controller 2/Sc, 2/DC, 4/DC, 4/SC, 3/QC, 3/DC, 3/DCL, 3/SC, 4/Di, and CERC ATA100/4CH, Device Driver for Windows NT 4.0
Version 4.21
Install Instructions
Download
1. Click the "Download Now" link to download the file. 2. If the Export Compliance Disclaimer window appears, click the "I agree" link to accept the agreement. 3. When the File Download window appears, click "Save" to save the file to your hard drive.
Extract Files
1. Browse to the location where you downloaded the file and double-click the new file to unzip the download package. 2. Specify the location to unzip the files – the instructions below assume you extract files to a formatted floppy disk. 3. Click on the unzip button to extract files.
Installation
Dell PowerEdge RAID Controller 4/DC, 4/SC, 3/QC, 3/DC, 3/DCL, 3/SC, 4/Di, and CERC ATA100/4CH, Device Driver for Windows NT 4.0
Version 4.21
This program creates a Windows NT 4.0 driver diskette for the controllers. You will need a formatted 3 1/2 inch floppy diskette for the following procedure.
1) Download the file to a directory on your hard drive. The file downloaded is a self-extracting executable.
2) Double click on the file to run the executable.
3) Click on the unzip button to extract files to the floppy.
Power down the system and install the PERC/CERC card. Configure the logical drives before proceeding with the driver install described below.
Performing a New Installation of Windows NT 4.0
"Making PERC/CERC the Primary Controller in Windows NT 4.0"
1) Boot the system using the Windows NT 4.0 CD. As the message "Setup is inspecting your computer's hardware configuration." appears. Press F6 immediately.
2) Within a few seconds, the Windows NT Setup screen appears, requesting additional adapters in the system. Press 'S' to specify an additional device, then press Enter on the OTHER option in the selection screen.
3) Insert the PERC/CERC driver diskette created above and press Enter. "CERC ATA100/4ch; PERC2/3/4 Series Windows NT Driver" appears. Press Enter to load the driver.
4) Press 'S' to load additional mass storage device driver if required. Otherwise, press Enter to continue installation process as usual. Windows NT 4.0 continues to be installed as usual. Please refer to the operating system installation documentation for further steps.
"Making PERC/CERC a Secondary Controller in Windows NT 4.0"
1) Start the Windows NT 4.0 installation process. Load the device for the primary controller if necessary.
2) Windows NT Server Setup screen is displayed after loading Windows NT Kernel. Press Enter to continue.
3) Setup displays mass storage devices that it has recognized in your computer. Press 'S' to specify an additional device, then press Enter on the OTHER option in the selection screen.
4) Insert the PERC/CERC driver diskette created above and press Enter. "CERC ATA100/4ch; PERC2/3/4 Series Windows NT Driver" appears. Press Enter to load the driver.
5) Press 'S' to load additional mass storage device drivers if required; otherwise, press Enter to continue the installation process as usual. Windows NT 4.0 continues to be installed as usual. Please refer to the operating system installation documentation for further steps.
Adding the PERC/CERC Driver to an Existing Windows NT 4.0 Server
If your server is already running Windows NT 4.0, then use the following steps to add the PERC/CERC Windows NT 4.0 driver.
1) Insert the PERC/CERC driver diskette created above in appropriate drive. The driver files can also be installed from a local or network drive.
2) Click on Start > Control Panel > Settings. Double-click on the Small Computer System Interface (SCSI) Adapter icon.
3) Select the Drivers tab.
4) Click on the Add button.
5) Select Have Disk.
6) The Install From Disk box appears. Specify the l