Dell Networking N4000 Series, Firmware Version 6.2.1.6,A07
Genstart er nødvendigInstalleretDenne fil blev automatisk installeret som en del af en nylig opdatering. Hvis du oplever problemer, kan du downloade og geninstallere manuelt.
Indholdet på denne side er muligvis blevet oversat automatisk. Udfyld formularen nederst på siden for at give feedback.
Denne fil blev automatisk installeret som en del af en nylig opdatering. Hvis du oplever problemer, kan du downloade og geninstallere manuelt.
Both Dell Networking N4000 Series switches and Dell PowerConnect 8100 Series shares the same firmware image version (for example., N4000v6.2.1.6.stk). Dell Networking PC8100 series switches can be stacked with Dell Networking N4000 series switches with the entire stack required to run 6.0.0.8 or later firmware (6.2.1.6). Dell Networking PC8100 series switches can support both 5.x and 6.x firmware versions, but Dell Networking N4000 can support only 6.0.0.8 and later firmware versions.
Please refer to the Release Notes for fixes and enhancements available in this release. "Release Notes" are included in the zip file - "Dell Networking_6.2.1.6_Release_Notes".
Please follow software update instructions included in the zip file - "Upgrading Dell Networking N4000 Series Switches From Version 6.x.x.x to 6.2.1.6 Firmware.pdf".
Note: PowerConnect 8100 Series switches with B1 CPU Revision require firmware version 5.1.0.1 or later (6.2.1.6) and cannot be downgraded to earlier releases. If this unit is to be deployed as a member within a stack, the entire stack will be required to run 5.1.0.1 or later firmware (6.2.1.6). The improved CPU version XLP308H-B1 version is not compatible with firmware 5.0.x.x. The 'show version' CLI command in the 5.1.0.1 release has been improved to identify the CPU version of the switch.
Anbefalet
Tjek kompatibilitet
Indtast produktoplysningerne for at få vist de seneste driveroplysninger for dit system
Indtast din Dell-servicekode eller -model
Vil du søge efter dit produkt? Indtast et produkt-id.Vis mig hvordan
Søgningen gav ingen resultater.Vi kunne ikke finde nogen match til din søgning. Rediger din søgning for at indtaste en servicekode (B959FS3) eller model (Latitude 5540), og prøv igen.
Denne driver er ikke kompatibel
Denne driver er ikke relevant for det valgte produkt. Vælg et andet produkt for at indtaste dine produktoplysninger for denne driver igen, eller gå til siden Produktsupport for at se alle drivere til et andet produkt.
Log på Windows som administrator for at bruge automatisk scanning. Hvis du allerede er logget på som administrator og får vist denne meddelelse, skal du genstarte enheden.Dit system administreres af din it-administrator, og funktionaliteten kan være begrænset.
Find flere opdateringer. Brug SupportAssist til at finde alle de seneste driveropdateringer til din enhed.
Programrettelser og forbedringer
New Features & Enhancements: -Added Port-Security Sticky-MAC feature -Added support configuration of AdvLinkMTU, and included option MTU in Router Advertisement Message -Kernel updates and SSL version upgrade to 1.0.1.m
Fixes: Case ID Summary 865050 - N2048P v6.1.2.4 VoIP phones assigned to wrong VLAN since the stack was upgraded to v6.1.1.7 878235 - Routing issue, null address in ARP table after VLAN manipulation 881612 - N2048 - 6.1.2.4: web timeout (HTTPS) does not depend on exce-timeout configuration 883154 - N2048P - 6.1.2.4: Stack master unit crashing issuing some 'show' CLIs 886897 - N30XX v6.1.2.4 Ports on VLAN with PVST/R-PVST disabled not learning MAC addresses after reboot 890563 - ARP resolution not happening for iSCSI traffic when iSCSI optimization is enabled 891874 - N2048 - 6.1.2.4: Switch not sending snmp trap notification for UP/DOWN status on loopback interfaces 890635 - N-Series - 6.1.2.4 - SNMP MIB Walk OID "1.3.6.1.4.1.674.10895.3000.1.2.100" returns URL http://0.0.0.0 896750 - N-Series - 6.1.2.4 - IPv6 connectivity failure after stack member failure on N4064F stack with Fluid FS 897308 - N-Series Port-Security VoIP/PC issue 903943 - N-Series - 6.2.0.5 - N3000 - Receive and transmit packets dropped > MTU counters increasing 907269 - N-Series - 6.2.0.5 - Add 1G SFP (PN# FTRJ1319P1BTL) transceiver support 813685 - UNH - IPv6 - N3000 - USGv6 Interoperability and Basic Conformance failures 873414 - UNH : Unconfigurations of MTU values using the command "no system jumbo mtu" does not take effect in the DUT, after the DUT is configured with some random mtu value in the range of 1298-9216. 913069 - UNH : OSPF neighbourship not coming up on the dauntless after stack initiate failover, with MTU configured as 1298 and OSPF interface configured with ignore-mtu. 913071 - UNH : No ICMPv6 Too Big message sent on the interface, when the packet arrived on an interfaces that has less MTU configured. 913074 - UNH : DUT must drop the packet that has multicast address whose scop field contains the reserved value 0 as per RFC4291,section 2.7(page 14), but the ipv6 mrouter table has the learned-entry. 913068 - UNH : DUT should forward the packet that has multicast address whose scop field contains the reserved value "F" as per RFC4291 of section 2.7(page 14), but the first ICMPv6 echo request packet is getting dropped 913078 - UNH : In USGv6 Basic Conformance, the tests failed showing the reason "The device under test does not generate an ICMPv6 Parameter Problem messages in response to invalid packets". 913077 - UNH : In USGv6 Basic Conformance, the tests failed showing the reason "The device under test does not generate an Echo Reply to packets containing Pad1 or PadN options.". 913072 - UNH : DUT has problem in configuring and propagating IPv6 parameter as per the "v6LC.2.2.7c" test mentioned in the UNH defect 901088 - Connection fd is corrupt sometimes in bgp neighbor connection list 913061 - Flash format optionis missing on N4000 Series Bootmenu. 906510 - Route loop in leaf-spine topology after bringing down the link between Leaf-1 and spine-2 913067 - 6.2: Allow period '.' in configuration of the hostname 876886 - N4064F - 6.1.2.4: ARP entries with 0000.0000.0000 mac-address 883154 - N2048P - 6.1.2.4: Stack master unit crashing issuing some 'show' CLIs 839620 - N4032F Static IP Routing Issue. 921285 - DFE should to be turned on for 10Gb copper ports on N4000 Series. 921287 - Hotswapping different modules on N4000 Series causes the switch to crash. 921322 - OSAPI semaphores don't work when two tasks are waiting on the same semaphore. 922468 - After save and reload sticky mode functionality is not properly working. 907697 - N20xx dot1x mac based authentication,clients behind phones can't forward traffic 920185 - N3000-6.2-Front 10G ports goes down when 10G SFP extension module is removed from the slot
Dell Technologies anbefaler, at denne opdatering installeres under den næste planlagte opdateringscyklus. Opdateringen indeholder ændringer, der skal opretholde systemets generelle tilstand. Den sørger for, at systemsoftwaren forbliver opdateret og kompatibel med andre systemmoduler (firmware, BIOS, drivere og software) og kan indeholde andre nye funktioner.
Please refer to the Release Notes for additional bug fixes and feature enhancements available in this release. "Release Notes" are included in the zip file - "Dell Networking_6.2.1.6_Release_Notes"
(1) Download the zip file - N4000v6.2.1.6a07.zip (2) Extract the image file "N4000v6.2.1.6.stk" from the zip file (3) Install the image to the switch by following the upgrade procedure "Upgrading Dell Networking N4000 Series Switches From Version 6.x.x.x to 6.2.1.6 Firmware.pdf" extracted from zip file.
Har du brug for hjælp til problemer med netværksforbindelsen?
Find en løsning i Dells fejlfindingsvejledning for netværk