Maxtor Aurora 15K U320 18GB 68 Pin, Aurora 15K U320 18GB 80 Pin, Aurora 15K U320 36GB 68 Pin, Aurora 15K U320 36GB 80 Pin, Aurora 15K U320 73GB 68 Pin, Aurora 15K U320 73GB 80 Pin, v.1.0, A00

Custom Instructions for BR67588.exe:

Utility must be placed on a non-write protected diskette.

NOTE: In order to create this diskette, the file must be downloaded to and executed on a system running Microsoft Windows.

Download
1. Click the "Download Now" link to download the file.
2. If the Export Compliance Disclaimer window appears, click the "I agree" link to accept the agreement.
3. When the File Download window appears, click "Save" to save the file to your hard drive.

Diskette Creation
1. Browse to the location where you downloaded the file and double-click the new file to create the diskette set.
2. Insert a blank diskette then click Continue.
3. After all the files have been copied to the last, click Finish.

Installation:
NOTE: BACKUP ALL DATA BEFORE RUNNING THIS PROGRAM. Do not remove power from the devices or disturb the devices in any way while the download is in progress. Dell, Inc is not Responsible for any data loss resulting from the use of this program

NOTE: Before proceeding with the update, refer to README.TXT file, section 4.0 "Using The Update Utility" for important information regarding the update process.

For drives connected to an LSI 1020 or 1030 SCSI controller:
1. Insert the firmware update diskette into the floppy drive and reboot the system.
2. The utility will automatically determine the correct device to update when booted
3. Once the update is complete Remove the diskette and reboot the system.

For drives connected to an Adapted 7899 or 39160 SCSI controller:
1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line Device=ASPIDRV\ASPI8U2.SYS and adding the ‘REM’ statement to the line Device=ASPIDRV\ASPIMPT.SYS. This modification loads the ASPI driver for Adaptec controllers instead of the ASPI driver for LSI controllers
2. Insert the firmware update diskette into the floppy drive and reboot the system.
3. The utility will automatically determine the correct device to update when booted
4. Once the update is complete Remove the diskette and reboot the system.

For drives connected to Channel 0 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC):
1. Insert the firmware update diskette into the floppy drive and reboot the system.
2. The utility will automatically determine the correct device to update when booted
3. Once the update is complete Remove the diskette and reboot the system.

For drives connected to Channel 1 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC):
1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line “Device=ASPIDRV\MEGASPI.SYS /a1” and adding the REM statement to the line “Device=ASPIDRV\MEGASPI.SYS /a0”.
2. Insert the firmware update diskette into the floppy drive and reboot the system.
3. The utility will automatically determine the correct device to update when booted
4. Once the update is complete Remove the diskette and reboot the system.

For drives connected an Adaptec RAID controller (PERC 3/Si, PERC 3/DI):
1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line "Device=ASPIDRV\ELITEAPI.SYS /M" and adding the ‘REM’ statement to the lines “Device=ASPIDRV\MEGASPI.SYS /a0” and “Device=ASPIDRV\MEGASPI.SYS /a1”.
2. Insert the firmware update diskette into the floppy drive and reboot the system.
3. The utility will automatically determine the correct device to update when booted
4. Once the update is complete Remove the diskette and reboot the system.