Download Files
File Format: This file format consists of a BIOS executable file. The Universal (Windows/MS DOS) format can be used to install from any Windows or MS DOS environment.
File Name: Precision_7x10_1.10.7.exe
File size: 9.1 MB
To ensure the integrity of your download, please verify the checksum value.
MD5: 833fb12733f1da6f92743d7886ff77ac
SHA1: 9d8d9d35eeb6345e701a7f4217c01c4d81383b99
SHA-256: 536f973589edf1756c450a060cdc8e3907f6655ae909be581a7845ac381bb08c
Fixes & Enhancements
Fixes:
- Fixed Free Fall Sensor application shows disabled when both HDD and SSD attached.
- Fixed PXE boot issue in legacy mode via DA200.
- Fixed Dell legacy E-dock external display problem at legacy boot mode.
- Fixed incorrect WWAN device status in BIOS setup menu.
- Fixed Dell dock still functional issue when set dock item disabled in Bios setup.
- Fixed legacy E-dock behavior when power on system with LID close.
- Fixed "Clear TPM" Option may sometimes be greyed out in BIOS setup.
- Fixed "Enable Attempt Legacy Boot" item cannot be enabled in BIOS setup.
Enhancements:
- Updated Embedded Controller Engine Firmware.
- Updated Intel Processor Micro code.
- Updated Intel Video BIOS.
- Enhanced LAN supportability for Dell dock.
- Improved boot time at no Intel Management Engine support environment.
Important Information
Important:
- Not suggested/allowed to downgrade BIOS to the version before 1.6.6
Supported Operating Systems
Installation instructions
BIOS Update Executable for Windows/DOS
Download
1. Click Download File to download the file.
2. When the File Download window appears, click Save to save the file to your hard drive.
Installation
Run the BIOS update utility from Windows environment
1. Browse to the location where you downloaded the file and double-click the new file.
2. Windows System will auto restart and update BIOS while system startup screen.
3. After BIOS update finished, system will auto reboot to take effect.
Run the BIOS update utility from DOS environment if Legacy Boot Mode(Non-Windows users)
1. Copy the downloaded file to a bootable DOS USB key.
2. Power on the system, then Press F12 key and Select "USB Storage Device" and Boot to DOS prompt.
3. Run the file by typing copied file name where the executable is located.
4. DOS System will auto restart and update BIOS while system startup screen.
5. After BIOS update finished, system will auto reboot to take effect.
Run the BIOS update utility from DOS environment if UEFI boot mode with Load Legacy Option disabled (Non-Windows users)
1. Copy the downloaded file to a bootable DOS USB key.
2. Power on the system, then go to BIOS Setup by pressing F2 and go to "General-Boot Sequence - Boot List Option".
3. Change "UEFI" to "Legacy" of Boot List Option.
4. Click "Apply","Exit" to save changes and reboot system.
5. Press F12, then Select "USB Storage Device" and Boot to DOS prompt.
6. Run the file by typing copied file name where the executable is located.
7. DOS system will auto restart and update BIOS while system startup screen.
8. After BIOS update finished, system will auto reboot.
9. Go to BIOS Setup by pressing F2 and go to "General > Boot Sequence > Boot List Option".
10. Change "Legacy" to "UEFI" Boot Option.
11. Go to "Exit > Exit Save Changes" and reboot system.
Note 1: You will need to provide a bootable DOS USB key. This executable file does not create the DOS system files.
Note 2: Please make sure you suspend BitLocker encryption before updating BIOS on a BitLocker enabled system.
If you don't enable BitLocker on your system you can ignore it.
Applies to
Precision 7510 system BIOS
Precision 7710 system BIOS