Dell Latitude E6230 System BIOS

Restart required

Do not turn off your computer or disconnect from the power source while updating the BIOS as this could harm your computer. During the update, your computer will restart and you may briefly see a black screen.

Before updating, please read the installation instructions and important information noted below.

hi testing

Driver Id : 0H68G

Importance : Critical

Version : A20, A20 Latest version Recommended version Latest and Recommended version

Release Date : 09 Jan 2019

Download Type : System BIOS

Category : BIOS

This package provides the Dell system BIOS update. BIOS is a firmware that is embedded on a small memory chip on the system board. It controls the keyboard, monitor, disk drives, and other devices. This update addresses the Intel security advisory INTEL-SA-00115. A security advisory is a statement when a product is impacted by a security vulnerability and a remedy is available.

Download Files

File Format: This file format consists of a BIOS executable file. The Universal (Windows/MS DOS) format can be used to install from any Windows or MS DOS environment.

File Name: E6230A20.exe

File size: 8.36 MB

To ensure the integrity of your download, please verify the checksum value.

MD5: 1e3dd6f7a89ace87e2c9bef5501aa294

SHA1: 87ed51dcb389b7d83525acc173db06061a640ff8

SHA-256: 9029e7cb25f144d885165f8faee98bfb637fef880ea3386d1765e4b9ffd86187

Download .EXE

Important Information

Dell Fast Boot BIOS Feature:
The Dell Windows 8 released BIOS adds a new feature that is called Fast Boot.
When upgrading from a Pre-Windows 8 released BIOS to a Windows 8 released BIOS this feature will be set in Thorough mode.
Setting this feature in minimal causes USB devices/ports to be disabled in the pre-OS environment.
If you are dependent on USB devices in the pre-OS environment this setting should remain in the Thorough mode setting.

Upgrading and Downgrading between Currently Released BIOS Images (Pre-Windows 8 released BIOS) and Windows 8 Feature Enhanced BIOS Images (Windows 8 released BIOS)
Upgrading: The new Windows 8 released BIOS contains new features and behavior, but the upgrade process for you is still unchanged.
Run the EXE application and the BIOS handles incorporating the new features and logic with your current settings.
After the upgrade, you will immediately see that one of the visible changes is the logo screen during boot, which only displays the logo at a larger size with no other information or text.

Installation instructions

Updating the BIOS from Windows

Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.

Download and Installation
1. Click Download File, to download the file.
2. Click Save to save the file to your hard drive.
3. Browse to the location where you downloaded the file and double-click the new file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.

Updating the BIOS from DOS (Non-Windows users)

Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com. If BitLocker is not enabled on your system, you can ignore this step.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.

Installation
Note: You must provide a bootable USB drive. This executable file does not create the DOS system files.
1. Copy the downloaded file to a bootable USB drive.
2. Power on the system and then Press the F12 key.
3. Select USB Storage Device and boot to the DOS prompt.
4. Run the file by typing following command. For example:
C:\ Latitude_E6230_X.Y.Z.exe
Where C is the drive letter of the USB device where the executable file is located and Latitude_E6230_X.Y.Z.exe is the name of the downloaded file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.

Updating the BIOS from DOS with UEFI boot mode enabled (Non-Windows users, Load Legacy Option Disabled)

Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com. If BitLocker is not enabled on your system, you can ignore this step.
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.

Installation
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system and then go to BIOS Setup by pressing the F2 key.
3. Go to General > Boot Sequence > Boot > Boot List Option.
4. Change UEFI to Legacy of Boot List Option.
5. Go to Exit > Save Changes and reboot system.
6. Press F12 and then select USB Storage Device and boot to the DOS prompt.
7. Run the file by typing the file name.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, the system restarts again.
8. Go to BIOS Setup by pressing the F2 key and go to General > Boot Sequence > Boot > Boot List Option.
9. Change Legacy to UEFI Boot Option.
10. Go to Exit > Save Changes and reboot the system.

Dell Latitude E6230 System BIOS

Download Files

Fixes & Enhancements

Important Information

Compatible Systems

Supported Operating Systems

Installation instructions

Applies to