Dell Networking N2000 Series, Firmware Version 6.5.2.9
Es necesario reiniciar. Instalado Se ha instalado este archivo automáticamente como parte de una actualización reciente. Si tiene algún problema, lo puede descargar y reinstalar manualmente.Es posible que el contenido de esta página se haya traducido automáticamente. Si desea proporcionar comentarios, complete el formulario de la parte inferior de la página.
If N2000 series switch has an earlier version of firmware (6.0.0.7 or 6.0.0.8 or 6.0.1.3), upgrade switch to the latest version of firmware 6.5.2.9 as it contains multiple bug fixes.
New CPLD version 20 is available in release 6.5.1.1 and later (6.5.2.9) for both N3000 and N2000 Series switches. After upgrading the switches to FW version 6.5.1.1 and later (6.5.2.9), the CPLD can be updated to version 20 from CLI using the command - "update cpld". To update CPLD on stack members, run - 'devshell cpldUpdate' command from serial console. Please DO NOT power-cycle the switch when CPLD update is in progress. After CPLD update is complete, the switch will reset on it's own. Verify CPLD Version with the command - 'show version' from CLI after switch boot-up completes.
****Below information is applicable ONLY for N2000/N3000 switches upgraded to 6.5.2.9 and CPLD Version 15 or 17 or 20 and attempt to downgrade to any prior FW version****
Downgrading N3000 and N2000 Series switches from firmware version 6.5.2.9 with the updated CPLD version 15 or 17 or 20 (Verify CPLD Version with the command “show version” from CLI) to any prior 6.x.x.x version can ONLY be done by downgrading via interim FW version B.6.3.2(N3000_N2000vB.6.3.2.stk) attached to zip file.
With interim FW image version B.6.3.2 running, the switches should be downgraded to CPLD version 13 first before downgrading to any 6.x.x.x version. Please follow the instructions documented in the “Firmware Downgrade” section of "Upgrading Dell EMC Networking N2000 Series Switches From Version 6.x.x.x to 6.5.2.9" procedure.
Please refer to the Release Notes for fixes and enhancements available in this release. "Release Notes" are included in the zip file - "Dell_EMC_Networking_6.5.2.9_6.5.2.39_Release_Notes(N1500_N2000_N3000_N3000E-ON_N4000_PC8100)".pdf"
New CPLD version 20 is available in release 6.5.1.1 and later (6.5.2.9) for both N3000 and N2000 Series switches. After upgrading the switches to FW version 6.5.1.1 and later (6.5.2.9), the CPLD can be updated to version 20 from CLI using the command - "update cpld". To update CPLD on stack members, run - 'devshell cpldUpdate' command from serial console. Please DO NOT power-cycle the switch when CPLD update is in progress. After CPLD update is complete, the switch will reset on it's own. Verify CPLD Version with the command - 'show version' from CLI after switch boot-up completes.
****Below information is applicable ONLY for N2000/N3000 switches upgraded to 6.5.2.9 and CPLD Version 15 or 17 or 20 and attempt to downgrade to any prior FW version****
Downgrading N3000 and N2000 Series switches from firmware version 6.5.2.9 with the updated CPLD version 15 or 17 or 20 (Verify CPLD Version with the command “show version” from CLI) to any prior 6.x.x.x version can ONLY be done by downgrading via interim FW version B.6.3.2(N3000_N2000vB.6.3.2.stk) attached to zip file.
With interim FW image version B.6.3.2 running, the switches should be downgraded to CPLD version 13 first before downgrading to any 6.x.x.x version. Please follow the instructions documented in the “Firmware Downgrade” section of "Upgrading Dell EMC Networking N2000 Series Switches From Version 6.x.x.x to 6.5.2.9" procedure.
Please refer to the Release Notes for fixes and enhancements available in this release. "Release Notes" are included in the zip file - "Dell_EMC_Networking_6.5.2.9_6.5.2.39_Release_Notes(N1500_N2000_N3000_N3000E-ON_N4000_PC8100)".pdf"
Recomendado
Comprobar compatibilidad
Introduzca los detalles del producto para ver la información del controlador más reciente para su sistemaIntroduzca la etiqueta de servicio de Dell o el modelo
¿Desea buscar un producto? Introduzca un identificador de producto. ¿Cómo lo hago?
Este controlador no es compatible.
Este controlador no es aplicable para el producto seleccionado. Elija otro producto si desea reintroducir los detalles del producto para este controlador o visite la página Asistencia para productos si desea ver todos los controladores disponibles para un producto distinto.
Inicie sesión en Windows como administrador para utilizar los análisis automáticos. Si ya ha iniciado sesión como administrador y ve este mensaje, reinicie el sistema. Su administrador de TI gestiona el sistema y es posible que haya funciones limitadas.
Busque más actualizaciones. Utilice SupportAssist para buscar las actualizaciones de controladores más recientes para su dispositivo.
Correcciones y mejoras
Fixes:
FIELD-2846,FIELD-2851,FIELD-2852,CS4789696-Under voltage detection warning and log shows VIN=1.25V
FIELD-2868,CS4971583-PSU failure logs
FIELD-2995,FIELD-2949,FIELD-3072,CS5237423-Switch goes thermal shutdown
FIELD-2989,CS5185018-Switch reboots on its own without crash log.
FIELD-2980,CS5186162-SNMPSET MIB OID .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.2.9.1.4. fails with commitFailed
FIELD-3002,CS5241581-Switch crashes with 'hapiMcAsyncTask' task.
FIELD-2972,CS5158072-ARP responses dropped (not reaching CPU) after ARP timeout expires for end hosts
FIELD-3006,CS5178704-Out of memory causing SSH failure, crypto-key generate failure and switch goes unresponsive after write.
FIELD-3034,CS5373126-Failed to remove IPSG binding for IP on interface from hardware.
Internal-Improve packet RX processing on stackable switch platforms.
FIELD-3031,CS5327765-Standalone switch crashes with 'osapiTimer' task.
CS5541938-MAC Address movement logging and traps
FIELD-3096,CS5754107-IP Phone got session reset every hour and cause phone service interruption when dot1x reauthentication enabled(default reauth = 3600)
FIELD-3104,CS5837205-N2048P/N3132-DHCP Client fails to get IP address assigned with dot1x mac-based authenticated port
Enhancements:
None
Más informaciónFIELD-2846,FIELD-2851,FIELD-2852,CS4789696-Under voltage detection warning and log shows VIN=1.25V
FIELD-2868,CS4971583-PSU failure logs
FIELD-2995,FIELD-2949,FIELD-3072,CS5237423-Switch goes thermal shutdown
FIELD-2989,CS5185018-Switch reboots on its own without crash log.
FIELD-2980,CS5186162-SNMPSET MIB OID .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.2.9.1.4. fails with commitFailed
FIELD-3002,CS5241581-Switch crashes with 'hapiMcAsyncTask' task.
FIELD-2972,CS5158072-ARP responses dropped (not reaching CPU) after ARP timeout expires for end hosts
FIELD-3006,CS5178704-Out of memory causing SSH failure, crypto-key generate failure and switch goes unresponsive after write.
FIELD-3034,CS5373126-Failed to remove IPSG binding for IP on interface from hardware.
Internal-Improve packet RX processing on stackable switch platforms.
FIELD-3031,CS5327765-Standalone switch crashes with 'osapiTimer' task.
CS5541938-MAC Address movement logging and traps
FIELD-3096,CS5754107-IP Phone got session reset every hour and cause phone service interruption when dot1x reauthentication enabled(default reauth = 3600)
FIELD-3104,CS5837205-N2048P/N3132-DHCP Client fails to get IP address assigned with dot1x mac-based authenticated port
Enhancements:
None
Versión
6.5.2.9, A38
Fecha de publicación
14 sept 2018
Tipo de descarga
Sistemas operativos
Categoría
Red
Importancia
OpcionalDell Technologies recomienda revisar esta actualización para determinar si se aplica a su sistema. La actualización contiene cambios que afectan solamente a ciertas configuraciones u ofrecen nuevas funciones que pueden aplicarse o no a su entorno.
Formatos disponibles Ver información importante
Formato de archivo: Extrae archivos directamente al disco local
Nombre de archivo: N2000v6.5.2.9.A38.zip
Tamaño de archivo: 169.27 MB
Se trata de un archivo de gran tamaño. Tardará un tiempo en descargarse, dependiendo de la velocidad de la conexión.
Descripción del formato:
Este formato de archivo se compone de un fichero de archivos que se pueden descomprimir en un directorio del disco duro. La instalación se puede realizar desde ese directorio.
Para garantizar la integridad de la descarga, compruebe el valor de la suma de comprobación.
MD5:
459f8b86b399a0cc8a25095229c15d8b
SHA1:
87d6af9fee153a508d44bd7de0288025c2197a74
SHA-256:
f89faed6afe30b695c9609ce00a4eb8f8d3f3dbd07896e23629f3a8925434917
Formato de archivo: Un archivo de texto que contiene información sobre correcciones y mejoras pensadas para el cliente
Nombre de archivo: N2000ReadMev6.5.2.9.A38.txt
Tamaño de archivo: 4.04 KB
Se trata de un archivo de gran tamaño. Tardará un tiempo en descargarse, dependiendo de la velocidad de la conexión.
Descripción del formato:
Este formato de archivo contiene texto sin formato que puede verse con un editor de texto estándar.
Para garantizar la integridad de la descarga, compruebe el valor de la suma de comprobación.
MD5:
7cf9b4c5c8fadf7e296961cc9da5e6d9
SHA1:
3fa9b8d1c6390e64a3f5ecfad990a02454d90e33
SHA-256:
11ab14f0b8176c7c38db2589ebc65ebe12fc554c0f34a44da1ca5bd300b784f5
Al realizar la descarga, acepta los términos del Acuerdo de licencia de software de Dell. (en ingles)
Información importante
Fixes:
FIELD-2846,FIELD-2851,FIELD-2852,CS4789696-Under voltage detection warning and log shows VIN=1.25V
FIELD-2868,CS4971583-PSU failure logs
FIELD-2995,FIELD-2949,FIELD-3072,CS5237423-Switch goes thermal shutdown
FIELD-2989,CS5185018-Switch reboots on its own without crash log.
FIELD-2980,CS5186162-SNMPSET MIB OID .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.2.9.1.4. fails with commitFailed
FIELD-3002,CS5241581-Switch crashes with 'hapiMcAsyncTask' task.
FIELD-2972,CS5158072-ARP responses dropped (not reaching CPU) after ARP timeout expires for end hosts
FIELD-3006,CS5178704-Out of memory causing SSH failure, crypto-key generate failure and switch goes unresponsive after write.
FIELD-3034,CS5373126-Failed to remove IPSG binding for IP on interface from hardware.
Internal-Improve packet RX processing on stackable switch platforms.
FIELD-3031,CS5327765-Standalone switch crashes with 'osapiTimer' task.
CS5541938-MAC Address movement logging and traps
FIELD-3096,CS5754107-IP Phone got session reset every hour and cause phone service interruption when dot1x reauthentication enabled(default reauth = 3600)
FIELD-3104,CS5837205-N2048P/N3132-DHCP Client fails to get IP address assigned with dot1x mac-based authenticated port
Enhancements:
None
FIELD-2846,FIELD-2851,FIELD-2852,CS4789696-Under voltage detection warning and log shows VIN=1.25V
FIELD-2868,CS4971583-PSU failure logs
FIELD-2995,FIELD-2949,FIELD-3072,CS5237423-Switch goes thermal shutdown
FIELD-2989,CS5185018-Switch reboots on its own without crash log.
FIELD-2980,CS5186162-SNMPSET MIB OID .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.2.9.1.4. fails with commitFailed
FIELD-3002,CS5241581-Switch crashes with 'hapiMcAsyncTask' task.
FIELD-2972,CS5158072-ARP responses dropped (not reaching CPU) after ARP timeout expires for end hosts
FIELD-3006,CS5178704-Out of memory causing SSH failure, crypto-key generate failure and switch goes unresponsive after write.
FIELD-3034,CS5373126-Failed to remove IPSG binding for IP on interface from hardware.
Internal-Improve packet RX processing on stackable switch platforms.
FIELD-3031,CS5327765-Standalone switch crashes with 'osapiTimer' task.
CS5541938-MAC Address movement logging and traps
FIELD-3096,CS5754107-IP Phone got session reset every hour and cause phone service interruption when dot1x reauthentication enabled(default reauth = 3600)
FIELD-3104,CS5837205-N2048P/N3132-DHCP Client fails to get IP address assigned with dot1x mac-based authenticated port
Enhancements:
None
Se aplica a
Dell N2024
Dell N2024P
Dell N2048
Dell N2048P
Instrucciones de instalación
(1) Download the zip file - N2000v6.5.2.9.A38.zip
(2) Extract the image file "N2000Stdv6.5.2.9.stk" from the zip file
(3) Install the image to the switch by following the upgrade procedure "Upgrading Dell EMC Networking N2000 Series Switches From Version 6.x.x.x to 6.5.2.9 Firmware.pdf" extracted from zip file.
(2) Extract the image file "N2000Stdv6.5.2.9.stk" from the zip file
(3) Install the image to the switch by following the upgrade procedure "Upgrading Dell EMC Networking N2000 Series Switches From Version 6.x.x.x to 6.5.2.9 Firmware.pdf" extracted from zip file.
¿Necesita ayuda para solucionar problemas de conexión de red?
Consulta la guía de solución de problemas de red de DellAyuda para controladores y tutoriales
Para ver más descargas, vaya a Controladores y descargas. Para obtener ayuda sobre cómo usar la información de esta página, visite Tutoriales y ayuda para controladores.