No apague la computadora ni la desconecte de la fuente de alimentación mientras se actualiza el BIOS, ya que podría dañarse la computadora. Durante la actualización, la computadora se reiniciará y es posible que vea brevemente una pantalla negra.
Antes de la actualización, lea las instrucciones de instalación y la información importante que se indica a continuación.
Alienware Area 51 R4 System BIOS
Reinicio requerido Instalada Este archivo se instaló automáticamente como parte de una actualización reciente. Si experimenta algún problema, puede descargarlo y reinstalarlo manualmente.Es posible que el contenido de esta página se traduzca automáticamente. Para proporcionar comentarios, complete el formulario en la parte inferior de la página.
This package contains the Dell system BIOS update. BIOS is a firmware package that is embedded on a small memory chip on the system board. It controls the keyboard, monitor, disk drives, and other devices. This update addresses the Intel Security Advisories INTEL-SA-00115 and INTEL-SA-00118. A security advisory is a statement when a security vulnerability impacts a product, and a remedy is available for the vulnerability.
Recomendado
Comprobar compatibilidad
Ingrese los detalles del producto para ver la información más reciente del controlador para el sistemaIngrese su modelo o etiqueta de servicio de Dell
¿Desea buscar su producto? Ingrese un identificador de producto. Mostrarme cómo
Este controlador no es compatible
Este controlador no se corresponde con el producto seleccionado. Elija otro producto para volver a ingresar los detalles del producto para este controlador o visite la página Soporte de productos para ver todos los controladores de un producto diferente.
Inicie sesión en Windows como administrador para utilizar el escaneo automático. Si ya inició sesión como administrador y ve este mensaje, reinicie el sistema. El administrador de TI administra el sistema y es posible que las funciones sean limitadas.
Encuentre más actualizaciones. Utilice SupportAssist para encontrar todas las actualizaciones de controladores más recientes para su dispositivo.
Correcciones y mejoras
- Updated CPU microcode to address the Intel Security Advisory INTEL-SA-00115 (CVE-2018-3639 and CVE-2018-3640).
- Firmware updates to address the Intel Security Advisory INTEL-SA-00118 (CVE-2018-3627).
Más información- Firmware updates to address the Intel Security Advisory INTEL-SA-00118 (CVE-2018-3627).
Versión
1.1.16, 1.1.16
Fecha de publicación
03 ago. 2018
Tipo de descarga
BIOS del sistema
Categoría
BIOS
Importancia
CríticosDell Technologies recomienda encarecidamente aplicar esta importante actualización tan pronto como sea posible. La actualización contiene correcciones de errores críticas y cambios para mejorar la funcionalidad, la confiabilidad y la estabilidad del sistema Dell. También puede incluir correcciones de seguridad y otras mejoras de funciones.
Formatos disponibles Ver información importante
Formato de archivo: Ejecutable del BIOS CPG para Windows/DOS
File Name: Alienware_Area_51_R4_1.1.16.exe
Tamaño del archivo: 7.88 MB
Este es un archivo grande. La descarga puede tardar, dependiendo de la velocidad de conexión.
Descripción del formato:
Este formato de archivo consiste en un archivo ejecutable de BIOS. El formato universal (Windows/MS DOS) se puede utilizar para la instalación desde cualquier entorno de Windows o MS DOS.
Para garantizar la integridad de su descarga, verifique el valor de la suma de comprobación.
MD5:
c0dab875653f15313d1ac62898d30886
SHA1:
34707a23df8c13777dcaece95451b29fcfa03e47
SHA-256:
b4908b695f4a2777d415c20823b7820f458a24431ce6e78fea61f4a677007f96
Al realizar la descarga, acepta los términos del Contrato de licencia de software de Dell. (en ingles)
Información importante
BIOS updates take no more than 5 minutes to be installed on your system. You can install the updates in the background while using the system.
Se aplica a
Dell Alienware Area 51 R3
Instrucciones de instalación
Updating the BIOS from Windows
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Note 3: Your system requires a restart after installing the BIOS. The restart can be deferred but must be completed to ensure that the update is installed.
Download and Installation
1. Click Download File.
2. Click Save to save the file to your hard drive.
3. Browse to the location where you downloaded the file.
4. Double-click the new file.
5. The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS (Non-Windows users)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Note 3: Your system requires a restart after installing the BIOS. The restart can be deferred but must be completed to ensure that the update is installed.
Installation
Note: You must provide a bootable USB drive. This executable file does not create the DOS system files.
1. Copy the downloaded file to a bootable USB drive.
2. Power on the system and then Press the F12 key.
3. Select USB Storage Device and boot to the DOS prompt.
4. Run the file by typing following command. For example:
C:\ Alienware_R4_X.Y.Z.exe
Where C is the drive letter of the USB device where the executable file is located and Alienware_R4_X.Y.Z.exe is the name of the downloaded file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS with UEFI boot mode enabled (Non-Windows users, Load Legacy Option Disabled)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Note 3: Your system requires a restart after installing the BIOS. The restart can be deferred but must be completed to ensure that the update is installed.
Installation
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system and then go to BIOS Setup by pressing the F2 key.
3. Go to General > Boot Sequence > Boot > Boot List Option.
4. Change UEFI to Legacy of Boot List Option.
5. Go to Exit > Save Changes and reboot system.
6. Press F12 and then select USB Storage Device and boot to the DOS prompt.
7. Run the file by typing the file name.
8. The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, the system restarts again.
9. Go to BIOS Setup by pressing the F2 key and go to General > Boot Sequence > Boot > Boot List Option.
10. Change Legacy to UEFI Boot Option.
11. Go to Exit > Save Changes and reboot the system.
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Note 3: Your system requires a restart after installing the BIOS. The restart can be deferred but must be completed to ensure that the update is installed.
Download and Installation
1. Click Download File.
2. Click Save to save the file to your hard drive.
3. Browse to the location where you downloaded the file.
4. Double-click the new file.
5. The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS (Non-Windows users)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Note 3: Your system requires a restart after installing the BIOS. The restart can be deferred but must be completed to ensure that the update is installed.
Installation
Note: You must provide a bootable USB drive. This executable file does not create the DOS system files.
1. Copy the downloaded file to a bootable USB drive.
2. Power on the system and then Press the F12 key.
3. Select USB Storage Device and boot to the DOS prompt.
4. Run the file by typing following command. For example:
C:\ Alienware_R4_X.Y.Z.exe
Where C is the drive letter of the USB device where the executable file is located and Alienware_R4_X.Y.Z.exe is the name of the downloaded file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS with UEFI boot mode enabled (Non-Windows users, Load Legacy Option Disabled)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Note 3: Your system requires a restart after installing the BIOS. The restart can be deferred but must be completed to ensure that the update is installed.
Installation
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system and then go to BIOS Setup by pressing the F2 key.
3. Go to General > Boot Sequence > Boot > Boot List Option.
4. Change UEFI to Legacy of Boot List Option.
5. Go to Exit > Save Changes and reboot system.
6. Press F12 and then select USB Storage Device and boot to the DOS prompt.
7. Run the file by typing the file name.
8. The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, the system restarts again.
9. Go to BIOS Setup by pressing the F2 key and go to General > Boot Sequence > Boot > Boot List Option.
10. Change Legacy to UEFI Boot Option.
11. Go to Exit > Save Changes and reboot the system.
¿Necesita ayuda con los problemas de BIOS?
Busque la solución en la guía de solución de problemas de BIOS de DellAyuda y tutoriales para controladores
Para obtener más descargas, vaya a Controladores y descargas. Para obtener ayuda con el uso de la información en esta página, visite Tutoriales y ayuda sobre controladores.