Télécharger les fichiers
Format de fichier : Les packages DUP (Dell Update Packages) au format Microsoft Windows 32 bits ont été conçus pour fonctionner sur les systèmes d’exploitation Microsoft Windows 64 bits. Les packages DUP (Dell Update Packages) au format Microsoft Windows 64 bits fonctionnent uniquement sur les systèmes d’exploitation Microsoft Windows 64 bits. Assurez-vous de choisir la mise à jour de pilote de périphérique adaptée à votre système d’exploitation.
Nom du fichier: RAID-DRVR-R57932.exe
Taille du fichier: 1020.57 KB
Afin de garantir l’intégrité de votre téléchargement, veuillez vérifier la valeur de la somme de contrôle.
MD5 : 077BF8FECD988C442B85718D1224102F
Format de fichier : Ce format de fichier comprend une archive de fichiers qui peut être décompressée sur un répertoire du disque dur. L’installation peut être effectuée à partir de ce répertoire.
Nom du fichier: PERC4-WS2K3-632-A01.exe
Taille du fichier: 95.88 KB
Correctifs et améliorations
Changes from 6.25:
1) Changes in the setup files, so that Scsiport driver should give the correct device number and function number to the miniport driver.
2) A timeout is implemented in the driver so that driver shouldn't wait infinitely for the firmware to acknowledge the interrupt.
3) The driver will return an error status for all the offline logical drives.
4) Utilities are issuing 0xc3 calls for getting the logical drive statistics. This is causing the system to crash. This bug has been fixed in the driver.
5) The driver is using Hal functions to program hierarchy bridges and SCSI chips when system goes to D3 standby state.
The use of Hal functions were not allowing the driver to pass the HCT test. So we have to disable the Hal calls in the previous releases. A workaround has been done in the driver whereby all the Hal calls have been replaced by its assembly equivalent.
6) During reset, the driver was not clearing all the pending commands whenever the firmware is not able to complete it.
7) Driver is allocating enough continuous memory for the FLASH_WRITE_BLOCK(0x2c) command.
8) The system gives a blue screen when one swaps the boot controller. This bug has been fixed by adding entries of all the supported controllers in the critical data base section of the registry through changes in the oemsetup.inf file.
9) The system was not waking up after a hibernation/standby operation. This bug was caused by the driver. The driver was trying to access PCI_CONFIG space from the ScsiRestartAdapter in the driver. This bug has been fixed by accessing the PCI_CONFIG space from the ScsiSetRunningConfig entry point.
10) A new command has been introduced to enhance the performance for SCSI I/O on non-raid SCSI channel.
11) In case of standby, the driver was not waiting for the firmware to get initialized. This resulted in the driver sending commands to the firmware even when the firmware is not initialized. The fix has been put in the driver. The driver is polling for the Firmware to get initialized before sending any commands to the firmware.
12) The PERC 3 Firmware was not able to handle multiple reserve commands for a logical drive. This was leading to reservation failures on some of the logical drives. A fix has been done in the driver where the driver would accept only one reservation call at a time and would allow it to complete before issuing any more commands to the firmware.
Systèmes d’exploitation pris en charge
Instructions d’installation
Custom Instructions for PERC4-WS2K3-632-A01.exe:
Note: In order to execute this file, it must be downloaded to a system running Microsoft Windows with an unzip utility installed.
Download
1. Click the "Download Now" link to download the file.
2. If the Export Compliance Disclaimer window appears, click the "I agree" link to accept the agreement.
3. When the File Download window appears, click "Save" to save the file to your hard drive.
Extract Files
1. Browse to the location where you downloaded the file and double-click the new file to unzip the download package.
2. Click Continue.
3. Specify the location to upzip the files.
4. Click on the OK button to extract files.
5. After a few seconds a dialog box will appear that says that all files were successfully unzipped. Click OK to exit from the installer.
Installation on a New Windows 2003 Server
1. Boot the system using the Windows 2003 CD. As the message "Press F6 if you need to install a third party SCSI or RAID driver." appears, press F6 immediately.
2. Within a few minutes, a screen appears that asks for additional adapters in the system. Choose 'S'.
3. You are prompted for the driver diskette. Insert the PERC/CERC Windows 2003 driver diskette in the floppy drive and press Enter.
4. A list of drivers for PERC/CERC controllers appears. Select the right driver for your installed controller and press Enter to load the driver.
5. A statement is presented saying the driver that you provided is older then the Windows driver. Press 'S' to use the driver on the floppy.
6. Press Enter again to continue installation process as usual.
Adding the PERC/CERC Driver to an Existing Windows 2003 Server
1. After installing the hardware and or enabling the PERC ROMB, boot the system to Windows 2003. The Found New Hardware
Wizard displays.
2. If you are installing the PERC 3/SC, PERC 4/DC PERC 4/SC,
PERC 4/DI or CERC ATA100/4CH, click on Next and skip to step 5. Otherwise, click Cancel on all the new devices.
3. Restart the system from the shutdown menu.
4. The Found New Hardware Wizard displays again when the system boots to Windows 2003. Click on Next.
5. Select Search for a suitable driver and click Next to continue.
6. Select Floppy disk drive, insert the PERC/CERC Windows 2003 driver diskette created above and click Next to continue.
7. Continue to click on Next and finish the installation.
8. The Found New Hardware Wizard screen appears one time for each PERC 3/SC, PERC 4/SC, PERC 4/DC controller, three times for each PERC 3/DC or PERC 3/DCL controller and four times for each PERC 3/QC. Repeat steps 5 - 7 for each time the wizard displays to complete installation of the card.
9. To confirm driver installation, right click on My Computer and select Manage. Click on Device Manager, then click on SCSI and RAID controllers to see the newly added PERC 3 controller(s) in the list.
10. After finishing the driver update, YOU MUST REBOOT YOUR SERVER.
Updating the PERC/CERC Driver to an Existing Windows 2003 Server
1. Insert the PERC 3 Windows 2003 driver diskette and click Next to continue
2. Position the mouse pointer to the my computer icon on your desktop and right click and select Manage.
3. Position the mouse pointer on Device Manager and click the left mouse button.
4. Position the mouse pointer on SCSI and RAID controllers and double click.
5. Select the PERC controller and double click.
6. Select the Driver tab
7. Select the Update Driver. The Upgrade Device Driver Wizard displays.
8. Select ”Install from a list of specific location” and click Next to continue.
9. Select “Search for the best driver in these locations” and make sure that the “search removable media (floppy, cd-rom,…)” option is checked. Then click on the Next button.
10. When you see the Completing Hardware Update Wizard window click on Finish. Don’t restart the computer at this time!
11. Close the SCSI and R