Do not turn off your computer or disconnect from the power source while updating the BIOS as this could harm your computer. During the update, your computer will restart and you may briefly see a black screen.
Before updating, please read the installation instructions and important information noted below.
Dell OptiPlex 5040 System BIOS
Újraindítás szükséges Telepítve Ez a fájl automatikusan települt egy korábbi frissítés részeként. Ha bármilyen problémát tapasztal, manuálisan letöltheti és újratelepítheti.Lehet, hogy az oldal tartalma gépi fordítás útján lett fordítva. Visszajelzés küldéséhez töltse ki az oldal alján található űrlapot.
This package contains the Dell system BIOS update. BIOS is a firmware package that is embedded on a small memory chip on the system board. It controls the keyboard, monitor, disk drives, and other devices. This update addresses the Intel Security Advisories INTEL-SA-00464 and INTEL-SA-00459. A security advisory is a statement when a security vulnerability impacts a product, and a remedy is available for the vulnerability.
Ajánlott
Kompatibilitás ellenőrzése
Kérjük, adja meg a termék adatait a rendszeréhez tartozó legfrissebb illesztőprograminformációk megtekintéséhez.Adja meg Dell-szervizcímkéjét vagy -modelljét
Szeretné kikeresni termékét? Adjon meg egy termékazonosítót. Mutasd meg, hogyan!
This driver is not compatible
This driver is not applicable for the selected product. Choose another product to re-enter your product details for this driver or visit the Product Support page to view all drivers for a different product.
Az automatikus ellenőrzés használatához jelentkezzen be a Windowsba rendszergazdaként. Ha már bejelentkezett rendszergazdaként, és látja ezt az üzenetet, kérjük, indítsa újra a számítógépet. A rendszert az IT-rendszergazda kezeli, és előfordulhat, hogy a funkciók köre korlátozott.
További frissítések. A SupportAssist segítségével megtalálhatja az eszközéhez elérhető legújabb illesztőprogram-frissítéseket.
Fixes & Enhancements
- Firmware updates to address the Intel Security Advisory INTEL-SA-00459 (CVE-2020-24507 and CVE-2020-8703).
- Firmware updates to address the Intel Security Advisory INTEL-SA-00464 (CVE-2020-24512).
- Firmware updates to address security vulnerabilities.
További információ- Firmware updates to address the Intel Security Advisory INTEL-SA-00464 (CVE-2020-24512).
- Firmware updates to address security vulnerabilities.
Verziószám
1.18.1, 1.18.1
Kibocsátás dátuma
29 júl. 2021
Letöltés típusa
Rendszer-BIOS
Kategória
BIOS
Fontosság
KritikusDell Technologies highly recommends applying this important update as soon as possible. The update contains critical bug fixes and changes to improve functionality, reliability, and stability of your Dell system. It may also include security fixes and other feature enhancements.
Elérhető formátumok View Important Information
Fájlformátum: CPG BIOS Executable for Windows/DOS
Fájlnév: OptiPlex_5040_1.18.1.exe
Fájlméret: 12.24 MB
Ez egy nagy fájl. A kapcsolat sebességétől függően a letöltés eltarthat egy ideig.
Formátum leírása:
This file format consists of a BIOS executable file. The Universal (Windows/MS DOS) format can be used to install from any Windows or MS DOS environment.
A letöltés integritásának biztosítása érdekében ellenőrizze az ellenőrző összeg értékét.
MD5:
39b9dd3e3117e31fdc4a679afd71a825
SHA1:
20b391098e53d4030ca75d50ca98b3e338b13abc
SHA-256:
47e111ffe2315e0e65934c64cb1a88089dbec0247efffa675f7184cc17e4f91c
A letöltéssel Ön elfogadja a Dell szoftverlicenc-szerződés feltételeit.
Fontos tudnivalók
- Once the BIOS is upgraded, you cannot downgrade the BIOS EXE/Recovery (RCV) to versions earlier than 1.1.1 due to restrictions. BIOS downgrades are restricted when there are security updates and important fixes with earlier versions that impact the functionality of the system.
- BIOS updates take no more than 5 minutes to be installed on your system. You can install the updates in the background while using the system.
- BIOS updates take no more than 5 minutes to be installed on your system. You can install the updates in the background while using the system.
A következőre vonatkozik:
OptiPlex 5040 System BIOS
Telepítési utasítások
Updating the BIOS from Windows
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Note 3: Your system requires a restart after installing the BIOS. The restart can be deferred but must be completed to ensure that the update is installed.
Download and Installation
1. Click Download File.
2. Click Save to save the file to your hard drive.
3. Browse to the location where you downloaded the file.
4. Double-click the new file.
5. The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS (Non-Windows users)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Note 3: Your system requires a restart after installing the BIOS. The restart can be deferred but must be completed to ensure that the update is installed.
Installation
Note: You must provide a bootable USB drive. This executable file does not create the DOS system files.
1. Copy the downloaded file to a bootable USB drive.
2. Power on the system and then Press the F12 key.
3. Select USB Storage Device and boot to the DOS prompt.
4. Run the file by typing following command. For example:
C:\ OptiPlex_5040_X.Y.Z.exe
Where C is the drive letter of the USB device where the executable file is located and OptiPlex_5040_X.Y.Z.exe is the name of the downloaded file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS with UEFI boot mode enabled (Non-Windows users, Load Legacy Option Disabled)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Note 3: Your system requires a restart after installing the BIOS. The restart can be deferred but must be completed to ensure that the update is installed.
Installation
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system and then go to BIOS Setup by pressing the F2 key.
3. Go to General > Boot Sequence > Boot > Boot List Option.
4. Change UEFI to Legacy of Boot List Option.
5. Go to Exit > Save Changes and reboot system.
6. Press F12 and then select USB Storage Device and boot to the DOS prompt.
7. Run the file by typing the file name.
8. The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, the system restarts again.
9. Go to BIOS Setup by pressing the F2 key and go to General > Boot Sequence > Boot > Boot List Option.
10. Change Legacy to UEFI Boot Option.
11. Go to Exit > Save Changes and reboot the system.
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Note 3: Your system requires a restart after installing the BIOS. The restart can be deferred but must be completed to ensure that the update is installed.
Download and Installation
1. Click Download File.
2. Click Save to save the file to your hard drive.
3. Browse to the location where you downloaded the file.
4. Double-click the new file.
5. The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS (Non-Windows users)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Note 3: Your system requires a restart after installing the BIOS. The restart can be deferred but must be completed to ensure that the update is installed.
Installation
Note: You must provide a bootable USB drive. This executable file does not create the DOS system files.
1. Copy the downloaded file to a bootable USB drive.
2. Power on the system and then Press the F12 key.
3. Select USB Storage Device and boot to the DOS prompt.
4. Run the file by typing following command. For example:
C:\ OptiPlex_5040_X.Y.Z.exe
Where C is the drive letter of the USB device where the executable file is located and OptiPlex_5040_X.Y.Z.exe is the name of the downloaded file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS with UEFI boot mode enabled (Non-Windows users, Load Legacy Option Disabled)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Note 3: Your system requires a restart after installing the BIOS. The restart can be deferred but must be completed to ensure that the update is installed.
Installation
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system and then go to BIOS Setup by pressing the F2 key.
3. Go to General > Boot Sequence > Boot > Boot List Option.
4. Change UEFI to Legacy of Boot List Option.
5. Go to Exit > Save Changes and reboot system.
6. Press F12 and then select USB Storage Device and boot to the DOS prompt.
7. Run the file by typing the file name.
8. The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, the system restarts again.
9. Go to BIOS Setup by pressing the F2 key and go to General > Boot Sequence > Boot > Boot List Option.
10. Change Legacy to UEFI Boot Option.
11. Go to Exit > Save Changes and reboot the system.
Segítségre van szüksége a BIOS-problémákkal kapcsolatban?
Keressen megoldást a Dell BIOS hibaelhárítási útmutatójábanIllesztőprogramokkal kapcsolatos súgó és oktatóanyagok
További letöltésekért lépjen a következő oldalra: Illesztőprogramok és letöltések. Az ezen az oldalon található információk használatával kapcsolatban látogasson el az illesztőprogramokkal kapcsolatos súgó és oktatóanyagok oldalára.