Dell Hybrid Cloud System for Microsoft Patch and Update (Minor)
Instalado Este arquivo foi instalado automaticamente como parte de uma atualização recente. Se você estiver enfrentando algum problema, poderá fazer download e reinstalar manualmente.O conteúdo desta página pode ter sido traduzido automaticamente. Para fazer comentários, preencha o formulário no fim da página.
Update 1901 for Cloud Platform System (CPS) Standard includes updates for Windows Server and other software and hardware components (firmware, BIOS, drivers and software).
Recomendado
Verificar compatibilidade
Digite os dados do seu produto para ver as informações mais recentes sobre o driver do sistemaDigite a etiqueta de serviço ou o modelo da Dell
Quer procurar o seu produto? Digite um identificador do produto. Mostre-me como
Este driver não é compatível
Este driver não é válido para o produto selecionado. Selecione outro produto para digitar novamente os dados do seu produto para este driver ou acesse a página Suporte a produtos para ver todos os drivers de um produto diferente.
Faça log-in no Windows como administrador para usar a verificação automática. Se você já estiver conectado como administrador e estiver vendo esta mensagem, reinicialize o sistema. O sistema é gerenciado pelo administrador da TI e pode haver poucos recursos.
Encontre mais atualizações. Use o SupportAssist para encontrar as atualizações de driver mais recentes para o seu dispositivo.
Correções e aprimoramentos
Server PowerEdge BIOS R630/R730/R730XD and PowerEdge C6320 Version 2.8.0 Fixes & Enhancements
Fixes:
- For memory sizes less than 1 TB, updated the MTRR algorithm to the same behavior as 2.4.3 and earlier BIOS versions.
Enhancements:
- Enhancement to address security vulnerability CVE-2018-3639 (https://cve.mitre.org/cgibin/cvename.cgi?name=CVE-2018-3639 ).
- Enhancement to address security vulnerability CVE-2018-3640 (https://cve.mitre.org/cgibin/cvename.cgi?name=CVE-2018-3640 ).
- Updated the Intel Xeon Processor E5-2600 v4 Product Family Processor Microcode to version 0x0b00002E.
- Updated the Xeon Processor E5-2600 v3 Product Family Processor Microcode to version 0x3D.
- Added setup option QPI Link L1 Power Management. Default is set to Enabled.
- Added setup option Lower Memory Mapped I/O Base to 512 GB. Default is set to Disabled.
- Added proper identification for maximum DIMM speed of 2666 MHz.
iDRAC with Lifecycle Controller Version 2.61.60.60 Fixes & Enhancements
Fixes:
- Fixed an issue where power supply mismatch was being
reported impacting power state of server
- Fixed an issue with firmware update when performing
firmware update of devices after LC wipe
Authentication:
- Changed the required privileges for configuring Directory
Services from the Operator role to Administrator role
- Fixed an issue that was allowing users with Operator
role to perform certain actions that require higher
privileges using Redfish
Security:
- Fixed an issue that was causing TLS 1.1 and TLS 1.2 ciphers
to be listed even if the iDRAC was configured to use TLS 1.2 only
- Fixed a CGI logout binary issue
- Fixed an issue that allowed users to stop the firmware
booting at U-boot by setting persistent U-boot variables
Enhancements:
- N/A
Intel NIC Family Version 18.8.0 Firmware for I350, I354, X520, X540, and X550 adapters Fixes & Enhancements
Note: Firmware downgrade from 18.8.x to 18.5.x or older versions is not supported.
Fixes
-Resolved an issue that may cause the link to stay down with both port LEDs off on Intel(R) 10G X520 LOM, Intel(R) 10G X520 rNDC and Intel(R) 10G 4P X520/I350 rNDC when firmware is upgraded to version 18.5.17.
Enhancements
- A reset is now enforced after UEFI iSCSI configuration parameters are updated to ensure previous iSCSI parameters are not used.
Dell 12Gbps HBA firmware version 16.17.00.03 Fixes & Enhancements
Fixes:
- Resolved an issue which would cause I/O latency during a cable failure in a multipath topology.
- Resolved several issues which could cause delays in recovery from communication errors on backplanes or external cabling.
- Fixed an issue where iDRAC / RACADM could lose communication with HBA until the systems was rebooted
- Improved device error recovery logic.
Enhancements:
- N/A
Dell PERC H330 Mini/Adapter RAID Controller firmware version 25.5.5.0005 Fixes & Enhancements
Fixes:
-Fixed an issue where congested "I2C 4 PID 10 TIMEOUT but stop sent!" PERC debug TTY log events are reported in 14G server systems.
-Fixed an issue in VMWare with a PERC 9 controller configured as a pass-through device which would report in the PERC debug TTY log a false error stating "345=Controller encountered a fatal error and was reset" during power-on of virtual machine, guest OS restart, or Guest OS shutdown.
-Fixed an issue where using Segmented Firmware Download (SFD) mode 7 to flash SATA drive FW on some SATA drive models would fail.
-Fixed an issue where system could hang after performing Cryptographic Erase only from CTRL-R on some ISE drive models.
-Fixed a corner case issue where reconnecting an external enclosure in which a "bad PHY" error condition exists could cause a virtual disk to become inaccessible.
-Fixed an issue in VMWare with a PERC 9 controller configured as a pass-through device that would not have firmware time sync after virtual machine starts
Ler maisFixes:
- For memory sizes less than 1 TB, updated the MTRR algorithm to the same behavior as 2.4.3 and earlier BIOS versions.
Enhancements:
- Enhancement to address security vulnerability CVE-2018-3639 (https://cve.mitre.org/cgibin/cvename.cgi?name=CVE-2018-3639 ).
- Enhancement to address security vulnerability CVE-2018-3640 (https://cve.mitre.org/cgibin/cvename.cgi?name=CVE-2018-3640 ).
- Updated the Intel Xeon Processor E5-2600 v4 Product Family Processor Microcode to version 0x0b00002E.
- Updated the Xeon Processor E5-2600 v3 Product Family Processor Microcode to version 0x3D.
- Added setup option QPI Link L1 Power Management. Default is set to Enabled.
- Added setup option Lower Memory Mapped I/O Base to 512 GB. Default is set to Disabled.
- Added proper identification for maximum DIMM speed of 2666 MHz.
iDRAC with Lifecycle Controller Version 2.61.60.60 Fixes & Enhancements
Fixes:
- Fixed an issue where power supply mismatch was being
reported impacting power state of server
- Fixed an issue with firmware update when performing
firmware update of devices after LC wipe
Authentication:
- Changed the required privileges for configuring Directory
Services from the Operator role to Administrator role
- Fixed an issue that was allowing users with Operator
role to perform certain actions that require higher
privileges using Redfish
Security:
- Fixed an issue that was causing TLS 1.1 and TLS 1.2 ciphers
to be listed even if the iDRAC was configured to use TLS 1.2 only
- Fixed a CGI logout binary issue
- Fixed an issue that allowed users to stop the firmware
booting at U-boot by setting persistent U-boot variables
Enhancements:
- N/A
Intel NIC Family Version 18.8.0 Firmware for I350, I354, X520, X540, and X550 adapters Fixes & Enhancements
Note: Firmware downgrade from 18.8.x to 18.5.x or older versions is not supported.
Fixes
-Resolved an issue that may cause the link to stay down with both port LEDs off on Intel(R) 10G X520 LOM, Intel(R) 10G X520 rNDC and Intel(R) 10G 4P X520/I350 rNDC when firmware is upgraded to version 18.5.17.
Enhancements
- A reset is now enforced after UEFI iSCSI configuration parameters are updated to ensure previous iSCSI parameters are not used.
Dell 12Gbps HBA firmware version 16.17.00.03 Fixes & Enhancements
Fixes:
- Resolved an issue which would cause I/O latency during a cable failure in a multipath topology.
- Resolved several issues which could cause delays in recovery from communication errors on backplanes or external cabling.
- Fixed an issue where iDRAC / RACADM could lose communication with HBA until the systems was rebooted
- Improved device error recovery logic.
Enhancements:
- N/A
Dell PERC H330 Mini/Adapter RAID Controller firmware version 25.5.5.0005 Fixes & Enhancements
Fixes:
-Fixed an issue where congested "I2C 4 PID 10 TIMEOUT but stop sent!" PERC debug TTY log events are reported in 14G server systems.
-Fixed an issue in VMWare with a PERC 9 controller configured as a pass-through device which would report in the PERC debug TTY log a false error stating "345=Controller encountered a fatal error and was reset" during power-on of virtual machine, guest OS restart, or Guest OS shutdown.
-Fixed an issue where using Segmented Firmware Download (SFD) mode 7 to flash SATA drive FW on some SATA drive models would fail.
-Fixed an issue where system could hang after performing Cryptographic Erase only from CTRL-R on some ISE drive models.
-Fixed a corner case issue where reconnecting an external enclosure in which a "bad PHY" error condition exists could cause a virtual disk to become inaccessible.
-Fixed an issue in VMWare with a PERC 9 controller configured as a pass-through device that would not have firmware time sync after virtual machine starts
Versão
1901, 1.5.10
Data da versão
06 mar. 2019
Tipo de download
Patch/atualização
Categoria
Imagens de software
Importância
EssencialA Dell Technologies recomenda aplicar esta atualização importante o mais rápido possível. A atualização contém correções de bugs e alterações importantes para melhorar a funcionalidade, a confiabilidade e a estabilidade do seu sistema Dell. Ela também pode incluir correções de segurança e outros aprimoramentos de recursos.
Formatos disponíveis Ver informações importantes
Formato do arquivo: Drivers de base para criação de imagens
Nome do arquivo: DHCS_Update_1.5.10.zip
Tamanho do arquivo: 1.21 GB
Este é um arquivo pesado. Dependendo da velocidade da sua conexão, o download pode demorar um tempo para ser concluído.
Descrição de formato:
Para garantir a integridade do download, verifique o valor da soma de verificação.
MD5:
b14b4cba4c9308eca15b512bde62ed75
SHA1:
588c2b88a609290a4429898254f3bf8f806deeba
SHA-256:
05d774c5ba684f14feffe7722e23cb02dcfd0efe49a999e8e20b582eb5635697
Ao fazer o download, você aceita os termos do Contrato de Licença de Software da Dell (em Inglês).
Informações importantes
- 1803 Patch and Update Package is a prerequisite.
- Use the Patch and Update framework to apply software and firmware updates. The Dell Hybrid Cloud System for Microsoft includes the Patch and Update (P&U) framework. This framework enables you to easily update the infrastructure components of the Dell Hybrid Cloud System for Microsoft stamp. The framework automates the installation of software, driver, and firmware updates on the physical hosts and the infrastructure VMs.
- Run the update package during a scheduled maintenance window when there is low activity. There is associated downtime for the infrastructure VMs if the package installs updates that require a server restart on the VMs.
- The patch and update mechanism does not target tenant workloads for software updates, so tenant VMs should not typically experience downtime. However, if an update package contains driver and firmware updates, there may be associated downtime. Check the information that is provided with the update package.
- Complete a full backup prior to installing the Patch and Update
- Intel NIC Firmware downgrade from 18.8.x to 18.5.x or older versions is not supported.
- Disable backups and tenant creation before starting the Patch and Update install.
- Use the Patch and Update framework to apply software and firmware updates. The Dell Hybrid Cloud System for Microsoft includes the Patch and Update (P&U) framework. This framework enables you to easily update the infrastructure components of the Dell Hybrid Cloud System for Microsoft stamp. The framework automates the installation of software, driver, and firmware updates on the physical hosts and the infrastructure VMs.
- Run the update package during a scheduled maintenance window when there is low activity. There is associated downtime for the infrastructure VMs if the package installs updates that require a server restart on the VMs.
- The patch and update mechanism does not target tenant workloads for software updates, so tenant VMs should not typically experience downtime. However, if an update package contains driver and firmware updates, there may be associated downtime. Check the information that is provided with the update package.
- Complete a full backup prior to installing the Patch and Update
- Intel NIC Firmware downgrade from 18.8.x to 18.5.x or older versions is not supported.
- Disable backups and tenant creation before starting the Patch and Update install.
Sistemas operacionais compatíveis
Windows Server 2012 R2
Instruções de instalação
Download
1. Click the "Download Now" link to download the file.
2. When the File Download window appears, click "Save" to save the file to your hard drive.
Installation
1. Browse to the location where you downloaded the file and extract the zip file.
2. Browse to the location where you extracted the file and double-click the exe file.
3. Read over the release information presented in dialog window.
4. Follow the DHCS Patch & Update Framework 1901 Guide for remaining steps to perform the update
1. Click the "Download Now" link to download the file.
2. When the File Download window appears, click "Save" to save the file to your hard drive.
Installation
1. Browse to the location where you downloaded the file and extract the zip file.
2. Browse to the location where you extracted the file and double-click the exe file.
3. Read over the release information presented in dialog window.
4. Follow the DHCS Patch & Update Framework 1901 Guide for remaining steps to perform the update
Ajuda e tutoriais para drivers
Para ver mais downloads, vá para Drivers e downloads. Para obter ajuda sobre como usar as informações contidas nesta página, visite Ajuda e tutoriais de driver.