Stäng inte av datorn eller koppla från strömkällan medan BIOS uppdateras. Annars kan datorn skadas. Under uppdateringen kommer datorn att startas om och en svart skärm kan visas en kort stund.
Läs installationsanvisningarna och den viktiga informationen nedan innan du uppdaterar.
Alienware X51 R3 System BIOS
Omstart krävs Installerad Den här filen installerades automatiskt som en del av en ny uppdatering. Om du har problem kan du ladda ner och installera om den manuellt.Innehållet på den här sidan kan ha översatts automatiskt. Fyll i formuläret längst ned på sidan för att ge feedback.
This package contains the Dell system BIOS update. It is supported on Dell Alienware X51 R3 system that runs the Windows and DOS operating systems. BIOS is a firmware that is embedded on a small memory chip on the system board. It controls the keyboard, monitor, disk drives, and other devices. This update addresses the Intel security advisories INTEL-SA-00213 and INTEL-SA-00233. A security advisory is a statement when a product is impacted by a security vulnerability and a remedy is available.
Rekommenderat
Kontrollera kompatibilitet
Ange din produktinformation för att se den senaste informationen om drivrutiner för ditt systemAnge din Dell service tag eller modell
Vill du söka efter din produkt? Ange en produktidentifierare. Visa mig hur
Den här drivrutinen är inte kompatibel
Den här drivrutinen gäller inte för den valda produkten. Välj en annan produkt för att ange din produktinformation för den här drivrutinen igen eller gå till produktsupportsidan för att visa alla drivrutiner för en annan produkt.
Logga in på Windows som administratör för att använda automatisk skanning. Om du redan är inloggad som administratör och ser det här meddelandet ska du starta om. Ditt system hanteras av IT-administratören och funktionerna kan vara begränsade.
Hitta fler uppdateringar. Använd SupportAssist för att hitta alla de senaste drivrutinsuppdateringarna för din enhet.
Korrigeringar och förbättringar
Fixes:
- Firmware updates to address security advisories INTEL-SA-00233(CVE-2018-12126,CVE-2018-12127,CVE-2018-12130 and CVE-2019-11091)
- Firmware updates to address security advisory INTEL-SA-00213 (CVE-2019-0086 CVE-2019-0091 CVE-2019-0093)
Enhancements:
- Not Applicable
Läs mer- Firmware updates to address security advisories INTEL-SA-00233(CVE-2018-12126,CVE-2018-12127,CVE-2018-12130 and CVE-2019-11091)
- Firmware updates to address security advisory INTEL-SA-00213 (CVE-2019-0086 CVE-2019-0091 CVE-2019-0093)
Enhancements:
- Not Applicable
Version
1.2.15, 1.2.15
Utgivningsdatum
26 juni 2019
Hämtningstyp
System-BIOS
Kategori
BIOS
Prioritet
KritiskDell Technologies rekommenderar starkt att du installerar den här viktiga uppdateringen så snart som möjligt. Uppdateringen innehåller kritiska buggfixar och ändringar som förbättrar funktionaliteten, pålitligheten och stabiliteten i ditt Dell-system. Den kan även innehålla säkerhetskorrigeringar och andra funktionsförbättringar.
Tillgängliga format
Filformat: Körbar CPG BIOS-fil för Windows/DOS
Filnamn: Alienware_X51_R3_1.2.15.exe
Filstorlek: 26.92 MB
Det här är en stor fil. Beroende på din anslutningshastighet kan det ta lite tid att ladda ner den.
Formatbeskrivning:
Det här filformatet består av en körbar BIOS-fil. Det universella formatet (Windows/MS DOS) kan användas för installation från alla Windows- eller MS DOS-miljöer.
Verifiera kontrollsummans värde så att hämtningen genomförs korrekt.
MD5:
44c123835a6e792fe6541b8bab146cd0
SHA1:
a3b3d454608a09b0c3e44c115a8440708ab5a146
SHA-256:
07f6fe840f34350af7ddee1afc95434579f29f7ef94ba2bf3217a2a63727c742
I och med att du hämtar accepterar du villkoren i Dells licensavtal för programvara. (på Engelska)
Gäller
Alienware-X51 R3
Installationsanvisningar
Updating the BIOS from Windows
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step.
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Download and Installation
1. Click Download File, to download the file.
2. Click Save to save the file to your hard drive.
3. Browse to the location where you downloaded the file and double-click the new file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS (Non-Windows users)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Installation
Note: You must provide a bootable USB drive. This executable file does not create the DOS system files.
1. Copy the downloaded file to a bootable USB drive.
2. Power on the system and then Press the F12 key.
3. Select USB Storage Device and boot to the DOS prompt.
4. Run the file by typing following command. For example:
C:\ Precision_5530_X.Y.Z.exe
Where C is the drive letter of the USB device where the executable file is located and Precision_5530_X.Y.Z.exe is the name of the downloaded file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS with UEFI boot mode enabled (Non-Windows users, Load Legacy Option Disabled)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step.
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Installation
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system and then go to BIOS Setup by pressing the F2 key.
3. Go to General > Boot Sequence > Boot > Boot List Option.
4. Change UEFI to Legacy of Boot List Option.
5. Go to Exit > Save Changes and reboot system.
6. Press F12 and then select USB Storage Device and boot to the DOS prompt.
7. Run the file by typing the file name.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, the system restarts again.
8. Go to BIOS Setup by pressing the F2 key and go to General > Boot Sequence > Boot > Boot List Option.
9. Change Legacy to UEFI Boot Option.
10. Go to Exit > Save Changes and reboot the system.
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step.
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Download and Installation
1. Click Download File, to download the file.
2. Click Save to save the file to your hard drive.
3. Browse to the location where you downloaded the file and double-click the new file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS (Non-Windows users)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Installation
Note: You must provide a bootable USB drive. This executable file does not create the DOS system files.
1. Copy the downloaded file to a bootable USB drive.
2. Power on the system and then Press the F12 key.
3. Select USB Storage Device and boot to the DOS prompt.
4. Run the file by typing following command. For example:
C:\ Precision_5530_X.Y.Z.exe
Where C is the drive letter of the USB device where the executable file is located and Precision_5530_X.Y.Z.exe is the name of the downloaded file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS with UEFI boot mode enabled (Non-Windows users, Load Legacy Option Disabled)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step.
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Installation
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system and then go to BIOS Setup by pressing the F2 key.
3. Go to General > Boot Sequence > Boot > Boot List Option.
4. Change UEFI to Legacy of Boot List Option.
5. Go to Exit > Save Changes and reboot system.
6. Press F12 and then select USB Storage Device and boot to the DOS prompt.
7. Run the file by typing the file name.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, the system restarts again.
8. Go to BIOS Setup by pressing the F2 key and go to General > Boot Sequence > Boot > Boot List Option.
9. Change Legacy to UEFI Boot Option.
10. Go to Exit > Save Changes and reboot the system.
Behöver du hjälp med BIOS-problem?
Hitta en lösning i Dells felsökningsguide för BIOSHjälp och självstudiekurser för drivrutiner
Fler hämtningar finns på Drivrutiner och hämtningsbara filer. Mer information om hur du använder sidan finns i Hjälp och anvisningar för drivrutiner