INTEL TAYLORSVILLE SATA SSD 6GB 100GB, 200GB, 400GB, and 800GB For Models SSDSC2BA100G3R, SSDSC2BA200G3R, SSDSC2BA400G3R, SSDSC2BA800G3R FW DL06
TakılıBu dosya son güncellemenin bir parçası olarak otomatik olarak yüklendi. Herhangi bir sorun yaşıyorsanız, manuel olarak indirip yeniden yükleyebilirsiniz.
Bu sayfa içeriği otomatik olarak çevrilmiş olabilir. Geri bildirim sağlamak için sayfanın en altındaki formu doldurun.
Bu dosya son güncellemenin bir parçası olarak otomatik olarak yüklendi. Herhangi bir sorun yaşıyorsanız, manuel olarak indirip yeniden yükleyebilirsiniz.
This release contains firmware version DL06 for Intel SSD (SSD 2.5" SATA) 100GB, 200GB, 400GB and 800GB Hard Drives.Vendor Models SSDSC2BA100G3R, SSDSC2BA200G3R, SSDSC2BA400G3R, SSDSC2BA800G3R
Önerilen
Uyumluluğu kontrol edin
Sisteminize yönelik en son sürücü bilgilerini görüntülemek için lütfen ürün ayrıntılarınızı girin
Sonuç bulunamadı.Aramanız için sonuç bulamadık. Lütfen bir servis etiketi (B959FS3) veya model (Latitude 5540) girerek aramanızı değiştirin ve tekrar deneyin.
Bu sürücü uyumlu değil
Bu sürücü, seçilen ürün için geçerli değildir. Ürün ayrıntılarınızı yeniden girmek için başka bir ürün seçin veya farklı bir ürüne yönelik tüm sürücüleri görüntülemek için Ürün Desteği sayfasını ziyaret edin.
Otomatik taramayı kullanmak için Windows'da yönetici olarak oturum açın. Zaten yönetici olarak oturum açtıysanız ve bu mesajı görüyorsanız lütfen yeniden başlatın.Sisteminiz BT yöneticiniz tarafından yönetiliyor ve özellikler sınırlı olabilir.
Daha fazla güncelleme bulun. SupportAssist'i kullanarak aygıtınız için en son sürücü güncellemelerini bulun.
Fixes & Enhancements
Added SCT command (0xC002) to read custom PHY settings Drive will automatically RESET after 500ms if power-off time is less than 500ms specification to allow proper drive enumeration after power-on Sanitize Crypto Scramble EXT command allowed in Disable Logical state, which will generate a new AES key and secure the drive Drive supports 512B and 4KB physical sector size As grown defects increase, SMART E8h value will decrease linearly After power cycle, the Timed Workload counters will resume from the last saved values and update after 60 minutes and every minute thereafter
Dell Technologies, bir sonraki zamanlanmış güncelleme döngünüzde bu güncellemeyi uygulamanızı önerir. Bu güncelleme, genel sistem durumunu korumaya yönelik değişiklikler içerir. Sistem yazılımının güncel ve diğer sistem modülleriyle (bellenim, BIOS, sürücüler ve yazılım) uyumlu kalmasını sağlar ve başka yeni özellikleri içerebilir.
Bu büyük bir dosyadır. Bağlantı hızınıza bağlı olarak indirme işlemi biraz zaman alabilir.
Biçim Açıklaması:
Dell Update Packages (DUP) in Microsoft Windows 32bit format have been designed to run on Microsoft Windows 64bit Operating Systems. Dell Update Packages (DUP) in Microsoft Windows 64bit format will only run on Microsoft Windows 64bit Operating Systems. When selecting a device driver update be sure to select the one that is appropriate for your operating system.
Bu büyük bir dosyadır. Bağlantı hızınıza bağlı olarak indirme işlemi biraz zaman alabilir.
Biçim Açıklaması:
Dell Update Packages for Linux can be used as stand-alone applications that ensure that specific validation criteria are met, then apply an update. Note: Update Packages for Linux are open source. See the Dell Update Packages for Linux Readme for details.
This update will not run if any of the following conditions exist 1. Any Virtual Disk that is not optimal. 2. A RAID container that is performing a Background Initialization or Consistency Check. 3. A Rebuild, Resync, or copyback function is taking place. 4. A RAID set that is Partially Degraded or in a Degraded state.
This update will run on drives remaining in a RAID set that is in a Offline state.
There is an architectural constraint with Dell DUP HDD firmware update utility, related to system memory utilization, which is typically encountered on systems with minimal system memory, memory-intensive configurations, multiple RAID controllers, or memory-intensive applications. This issue is typically reported as - The operation was not successful because the device buffer write has failed. And will result in an aborted attempt to update firmware on the identified HDD. Error codes associated with this failure mode include 8009 and 8017. Once an error is detected, the update session is aborted. There is no data integrity or data availability risk associated with this issue. Subsequent attempts to update the HDD firmware may succeed, particularly if system resources are freed up.
1. Click the "Download Now" link to download the file. 2. When the File Download window appears, click "Save" to save the file to your hard drive.
Installation
1. Browse to the location where you downloaded the file and double-click the new file. 2. Read over the release information presented in the dialog window. 3. Download and install any prerequisites identified in the dialog window before proceeding. 4. Click the Install button. 5. Follow the remaining prompts to perform the update.