Do not turn off your computer or disconnect from the power source while updating the BIOS as this could harm your computer. During the update, your computer will restart and you may briefly see a black screen.
Before updating, please read the installation instructions and important information noted below.
Dell G5 5587/G7 7588 and Vostro 7580 System BIOS
Restart required Takılı Bu dosya son güncellemenin bir parçası olarak otomatik olarak yüklendi. Herhangi bir sorun yaşıyorsanız, manuel olarak indirip yeniden yükleyebilirsiniz.Bu sayfa içeriği otomatik olarak çevrilmiş olabilir. Geri bildirim sağlamak için sayfanın en altındaki formu doldurun.
This package contains the Dell System BIOS update. BIOS is a firmware that is embedded on a small memory chip on the system board. It controls the keyboard, monitor, disk drives, and other devices. The update addresses the Intel security advisories INTEL-SA-00142, INTEL-SA-00125, INTEL-SA-00141, and INTEL-SA-00131. A security advisory is a statement when a product is impacted by a security vulnerability and a remedy is available. This update also fixes the issue where the system stops responding when an incorrectly formatted password is entered at the BIOS Security Manager (BIOS pre-boot password) prompt.
Önerilen
Uyumluluğu kontrol edin
Sisteminize yönelik en son sürücü bilgilerini görüntülemek için lütfen ürün ayrıntılarınızı girinDell Servis Etiketinizi veya modelinizi girin
Ürününüzü aramak mı istiyorsunuz? Bir ürün tanımlayıcısı girin. Nasıl yapılacağını göster
Bu sürücü uyumlu değil
Bu sürücü, seçilen ürün için geçerli değildir. Ürün ayrıntılarınızı yeniden girmek için başka bir ürün seçin veya farklı bir ürüne yönelik tüm sürücüleri görüntülemek için Ürün Desteği sayfasını ziyaret edin.
Otomatik taramayı kullanmak için Windows'da yönetici olarak oturum açın. Zaten yönetici olarak oturum açtıysanız ve bu mesajı görüyorsanız lütfen yeniden başlatın. Sisteminiz BT yöneticiniz tarafından yönetiliyor ve özellikler sınırlı olabilir.
Daha fazla güncelleme bulun. SupportAssist'i kullanarak aygıtınız için en son sürücü güncellemelerini bulun.
Fixes & Enhancements
Fixes:
- Firmware updates to address the security advisory INTEL-SA-00142 (CVE-2018-3659).
- Firmware updates to address the security advisory INTEL-SA-00125 (CVE-2018-3655).
- Firmware updates to address the security advisory INTEL-SA-00141 (CVE-2018-3657, CVE-2018-3658 and CVE-2018-3616).
- Firmware updates to address the security advisory INTEL-SA-00131 (CVE-2018-3643 and CVE-2018-3644).
- Fixed the issue where the system stops working when an incorrectly formatted password is entered at the BIOS Security Manager (BIOS pre-boot password) prompt.
- Fixed an issue with binary image measurement using the Linux UEFI shim boot loader.
- Fixed the TPM startup error when resuming from sleep mode.
- Fixed the issue where the system keeps rebooting after loading customer user setting with Legacy enabled.
- Fixed the issue where a warning message is displayed after every reboot when Thunderbolt auto switch is enabled.
Enhancements:
- Added BIOS Password Feature: Master Password Lockout.
- Improved type-C experience on device discovery and hot plug.
- Reduced the palm rest temperature and fan noise while gaming.
Read More- Firmware updates to address the security advisory INTEL-SA-00142 (CVE-2018-3659).
- Firmware updates to address the security advisory INTEL-SA-00125 (CVE-2018-3655).
- Firmware updates to address the security advisory INTEL-SA-00141 (CVE-2018-3657, CVE-2018-3658 and CVE-2018-3616).
- Firmware updates to address the security advisory INTEL-SA-00131 (CVE-2018-3643 and CVE-2018-3644).
- Fixed the issue where the system stops working when an incorrectly formatted password is entered at the BIOS Security Manager (BIOS pre-boot password) prompt.
- Fixed an issue with binary image measurement using the Linux UEFI shim boot loader.
- Fixed the TPM startup error when resuming from sleep mode.
- Fixed the issue where the system keeps rebooting after loading customer user setting with Legacy enabled.
- Fixed the issue where a warning message is displayed after every reboot when Thunderbolt auto switch is enabled.
Enhancements:
- Added BIOS Password Feature: Master Password Lockout.
- Improved type-C experience on device discovery and hot plug.
- Reduced the palm rest temperature and fan noise while gaming.
Version
1.5.0, 1.5.0
Sürüm tarihi
08 Eki 2018
İndirme Türü
Sistem BIOS
Kategori
BIOS
Önem
KritikDell Technologies, bu önemli güncellemeyi mümkün olan en kısa sürede uygulamanızı kesinlikle önerir. Bu güncelleme, Dell sisteminizin işlevselliğini, güvenilirliğini ve kararlılığını iyileştirmeye yönelik kritik hata düzeltmeleri ve değişiklikler içerir. Ayrıca güvenlik düzeltmeleri ve başka özellik iyileştirmeleri de içerebilir.
Kullanılabilir biçimler View Important Information
Dosya Biçimi: Windows/DOS için CPG BIOS Yürütülebilir Dosyası
Dosya Adı: Dell_G5_5587_G7_7588_Vostro_7580_1.5.0.exe
Dosya Boyutu: 7.87 MB
Bu büyük bir dosyadır. Bağlantı hızınıza bağlı olarak indirme işlemi biraz zaman alabilir.
Biçim Açıklaması:
This file format consists of a BIOS executable file. The Universal (Windows/MS DOS) format can be used to install from any Windows or MS DOS environment.
İndirme işleminizin bütünlüğünü sağlamak için lütfen sağlama toplamı değerini doğrulayın.
MD5:
2e3db98415d5ae9079fdf4b35d32726e
SHA1:
ddbeaf551fd6883ebabf21fc9b6b07ddc0bf43c1
SHA-256:
b88bbfd8b31a5536aa66789738e936e21a5f7ef44e911f06febbf9c0cbab17a2
İndirdiğinizde, Dell Software Lisans Sözleşmesi’nin koşullarını kabul etmiş olursunuz.
Important Information
BIOS cannot be downgraded to the version before 1.4.1.
Şunlar için geçerlidir:
Dell G5 5587 / Dell G7 7588 / Vostro 7580
Kurulum talimatları
Updating the BIOS from Windows
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Download and Installation
1. Click Download File, to download the file.
2. Click Save to save the file to your hard drive.
3. Browse to the location where you downloaded the file and double-click the new file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS (Non-Windows users)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Installation
Note: You must provide a bootable USB drive. This executable file does not create the DOS system files.
1. Copy the downloaded file to a bootable USB drive.
2. Power on the system and then Press the F12 key.
3. Select USB Storage Device and boot to the DOS prompt.
4. Run the file by typing following command. For example:
C:\ Precision_5530_X.Y.Z.exe
Where C is the drive letter of the USB device where the executable file is located and Precision_5530_X.Y.Z.exe is the name of the downloaded file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from BIOS Boot Menu (independent of operating system)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step.
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Installation
1. Copy the downloaded file to a USB drive. The USB drive does not need to be bootable device.
2. Insert the USB drive into any USB port.
3. Power on the system.
4. At the DELL logo screen, press F12 to access the one-time boot menu.
5. Select BIOS Flash Update in the Other Options section.
6. Click the ... button to browse the USB drive to locate the downloaded file.
7. Select the file and click Ok.
8. Verify the existing system BIOS information and the BIOS update information.
9. Click Begin Flash Update.
10. Review the Warning message and click Yes to proceed with the update.
The system restarts and displays a progress bar at the Dell logo screen. The system restarts again when the update is complete.
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Download and Installation
1. Click Download File, to download the file.
2. Click Save to save the file to your hard drive.
3. Browse to the location where you downloaded the file and double-click the new file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS (Non-Windows users)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Installation
Note: You must provide a bootable USB drive. This executable file does not create the DOS system files.
1. Copy the downloaded file to a bootable USB drive.
2. Power on the system and then Press the F12 key.
3. Select USB Storage Device and boot to the DOS prompt.
4. Run the file by typing following command. For example:
C:\ Precision_5530_X.Y.Z.exe
Where C is the drive letter of the USB device where the executable file is located and Precision_5530_X.Y.Z.exe is the name of the downloaded file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from BIOS Boot Menu (independent of operating system)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step.
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Installation
1. Copy the downloaded file to a USB drive. The USB drive does not need to be bootable device.
2. Insert the USB drive into any USB port.
3. Power on the system.
4. At the DELL logo screen, press F12 to access the one-time boot menu.
5. Select BIOS Flash Update in the Other Options section.
6. Click the ... button to browse the USB drive to locate the downloaded file.
7. Select the file and click Ok.
8. Verify the existing system BIOS information and the BIOS update information.
9. Click Begin Flash Update.
10. Review the Warning message and click Yes to proceed with the update.
The system restarts and displays a progress bar at the Dell logo screen. The system restarts again when the update is complete.
BIOS sorunlarıyla ilgili yardıma mı ihtiyacınız var?
Dell'in BIOS sorun giderme kılavuzundan bir çözüm bulunSürücülerle ilgili yardım ve öğreticiler
Daha fazla indirme için bkz. Sürücüler ve indirmeler. Bu sayfadaki bilgileri kullanmayla ilgili yardım almak için lütfen Sürücü Yardımı ve Öğretici Videoları bölümünü ziyaret edin.