Dell Networking OS10 S5200- oder S4148U-Port wird aufgrund eines falschen Portgruppenprofils nicht angezeigt
Summary: Zweifelsfrei funktionierendes Kabel und Transceiver angeschlossen, aber der Port wird nicht angezeigt. Es wurde überprüft, dass der Port nicht heruntergefahren ist. Warum wird der Port nicht angezeigt? ...
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Instructions
Switch-Modelle
S4148U
, S5200
Softwareversion
OS10
So ändern Sie den Portgruppenmodus
Die Portgruppe ist möglicherweise nicht für die Verhandlung mit der angegebenen Geschwindigkeit konfiguriert.
| Befehle | Beschreibung |
|---|---|
show port-group |
Hier werden alle Portgruppen und ihre derzeitige Konfiguration angezeigt. |
Benachrichtigt die zu ändernde
Portgruppennummer Wir suchen nach Port 56.
Beispiel aus dem S5200:
OS10# show port-group
Port-group Mode Ports FEM
port-group1/1/1 Eth 25g-4x 1 2 3 4 -
port-group1/1/2 Eth 10g-4x 5 6 7 8 -
port-group1/1/3 Eth 10g-4x 9 10 11 12 -
port-group1/1/4 Eth 10g-4x 13 14 15 16 -
port-group1/1/5 Eth 25g-4x 17 18 19 20 -
port-group1/1/6 Eth 25g-4x 21 22 23 24 -
port-group1/1/7 Eth 25g-4x 25 26 27 28 -
port-group1/1/8 Eth 25g-4x 29 30 31 32 -
port-group1/1/9 Eth 25g-4x 33 34 35 36 -
port-group1/1/10 Eth 10g-4x 37 38 39 40 -
port-group1/1/11 Eth 25g-4x 41 42 43 44 -
port-group1/1/12 Eth 25g-4x 45 46 47 48 -
port-group1/1/13 Eth 40g-2x 49 50 -
port-group1/1/14 Eth 40g-2x 51 52 -
port-group1/1/15 Eth 100g-1x 53 -
port-group1/1/16 Eth 100g-1x 54 -
port-group1/1/17 Eth 100g-1x 55 -
port-group1/1/18 Eth 100g-1x 56 -
Beispiel aus S4148U:
OS10# show port-group Port-group Mode Ports FEM port-group1/1/1 Eth 10g-4x 1 2 3 4 - port-group1/1/2 FC 16g-2x 5 6 7 8 - port-group1/1/3 FC 16g-2x 9 10 11 12 - port-group1/1/4 FC 16g-2x 13 14 15 16 - port-group1/1/5 FC 16g-2x 17 18 19 20 - port-group1/1/6 Eth 10g-4x 21 22 23 24 - port-group1/1/7 Eth 100g-1x 25 - port-group1/1/8 Eth 40g-1x 26 - port-group1/1/9 Eth 100g-1x 29 - port-group1/1/10 Eth 40g-1x 30 -
Beispiel:
| Befehle | Beschreibung |
|---|---|
OS10# show port-group |
Hier werden alle Portgruppen und ihre derzeitige Konfiguration angezeigt. |
OS10(config)# port-group 1/1/18 |
Wählen Sie den Port aus, den Sie ändern möchten |
OS10(conf-pg-1/1/18)# mode eth 40g-1x |
Geben Sie die Geschwindigkeit an, mit der Sie den Port festlegen möchten |
Bestätigung:
<165>1 2019-09-11T23:21:00.470567+00:00 S5248F-ON-U24 dn_ifm 852 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %IFM_ASTATE_UP: Interface admin state up :ethernet1/1/56:1
Überprüfen Sie, ob sich die Portgruppe geändert hat:
OS10# show port-group
Port-group Mode Ports FEM
port-group1/1/1 Eth 25g-4x 1 2 3 4 -
port-group1/1/2 Eth 10g-4x 5 6 7 8 -
port-group1/1/3 Eth 10g-4x 9 10 11 12 -
port-group1/1/4 Eth 10g-4x 13 14 15 16 -
port-group1/1/5 Eth 25g-4x 17 18 19 20 -
port-group1/1/6 Eth 25g-4x 21 22 23 24 -
port-group1/1/7 Eth 25g-4x 25 26 27 28 -
port-group1/1/8 Eth 25g-4x 29 30 31 32 -
port-group1/1/9 Eth 25g-4x 33 34 35 36 -
port-group1/1/10 Eth 10g-4x 37 38 39 40 -
port-group1/1/11 Eth 25g-4x 41 42 43 44 -
port-group1/1/12 Eth 25g-4x 45 46 47 48 -
port-group1/1/13 Eth 40g-2x 49 50 -
port-group1/1/14 Eth 40g-2x 51 52 -
port-group1/1/15 Eth 100g-1x 53 -
port-group1/1/16 Eth 100g-1x 54 -
port-group1/1/17 Eth 100g-1x 55 -
port-group1/1/18 Eth 40g-1x 56 -
Software-Fix
Betrieb wie vorgesehen
Affected Products
PowerSwitch S4112F-ON/S4112T-ON, PowerSwitch S4148F-ON/S4148T-ON/S4148FE-ON, PowerSwitch S4148U-ON, PowerSwitch S5212F-ON, PowerSwitch S5224F-ON, PowerSwitch S5248F-ONArticle Properties
Article Number: 000128222
Article Type: How To
Last Modified: 26 Nov 2025
Version: 8
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.