El puerto Dell Networking OS10 S5200 o S4148U no aparece debido a un perfil de grupo de puertos incorrecto
Summary: Se conectaron el cable y el transceptor en buen estado, pero el puerto no aparece. Se verificó que el puerto no se haya apagado. ¿Por qué no aparece el puerto?
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Instructions
Modelos de switches
S4148U
, S5200
Versión de software
OS10
Cómo cambiar el modo de grupo de puertos
Es posible que el grupo de puertos no esté configurado para negociar a la velocidad especificada.
| Comandos | Descripción |
|---|---|
show port-group |
Esto muestra todos los grupos de puertos y cómo están configurados actualmente. |
Anota el número de grupo de puertos que se modificará
. Estamos buscando el puerto 56.
Ejemplo de S5200:
OS10# show port-group
Port-group Mode Ports FEM
port-group1/1/1 Eth 25g-4x 1 2 3 4 -
port-group1/1/2 Eth 10g-4x 5 6 7 8 -
port-group1/1/3 Eth 10g-4x 9 10 11 12 -
port-group1/1/4 Eth 10g-4x 13 14 15 16 -
port-group1/1/5 Eth 25g-4x 17 18 19 20 -
port-group1/1/6 Eth 25g-4x 21 22 23 24 -
port-group1/1/7 Eth 25g-4x 25 26 27 28 -
port-group1/1/8 Eth 25g-4x 29 30 31 32 -
port-group1/1/9 Eth 25g-4x 33 34 35 36 -
port-group1/1/10 Eth 10g-4x 37 38 39 40 -
port-group1/1/11 Eth 25g-4x 41 42 43 44 -
port-group1/1/12 Eth 25g-4x 45 46 47 48 -
port-group1/1/13 Eth 40g-2x 49 50 -
port-group1/1/14 Eth 40g-2x 51 52 -
port-group1/1/15 Eth 100g-1x 53 -
port-group1/1/16 Eth 100g-1x 54 -
port-group1/1/17 Eth 100g-1x 55 -
port-group1/1/18 Eth 100g-1x 56 -
Ejemplo de S4148U:
OS10# show port-group Port-group Mode Ports FEM port-group1/1/1 Eth 10g-4x 1 2 3 4 - port-group1/1/2 FC 16g-2x 5 6 7 8 - port-group1/1/3 FC 16g-2x 9 10 11 12 - port-group1/1/4 FC 16g-2x 13 14 15 16 - port-group1/1/5 FC 16g-2x 17 18 19 20 - port-group1/1/6 Eth 10g-4x 21 22 23 24 - port-group1/1/7 Eth 100g-1x 25 - port-group1/1/8 Eth 40g-1x 26 - port-group1/1/9 Eth 100g-1x 29 - port-group1/1/10 Eth 40g-1x 30 -
Ejemplo:
| Comandos | Descripción |
|---|---|
OS10# show port-group |
Esto muestra todos los grupos de puertos y cómo están configurados actualmente. |
OS10(config)# port-group 1/1/18 |
Seleccione el puerto que desea modificar |
OS10(conf-pg-1/1/18)# mode eth 40g-1x |
Especifique la velocidad a la que desea establecer el puerto |
Confirmación:
<165>1 2019-09-11T23:21:00.470567+00:00 S5248F-ON-U24 dn_ifm 852 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %IFM_ASTATE_UP: Interface admin state up :ethernet1/1/56:1
Verifique que el grupo de puertos haya cambiado:
OS10# show port-group
Port-group Mode Ports FEM
port-group1/1/1 Eth 25g-4x 1 2 3 4 -
port-group1/1/2 Eth 10g-4x 5 6 7 8 -
port-group1/1/3 Eth 10g-4x 9 10 11 12 -
port-group1/1/4 Eth 10g-4x 13 14 15 16 -
port-group1/1/5 Eth 25g-4x 17 18 19 20 -
port-group1/1/6 Eth 25g-4x 21 22 23 24 -
port-group1/1/7 Eth 25g-4x 25 26 27 28 -
port-group1/1/8 Eth 25g-4x 29 30 31 32 -
port-group1/1/9 Eth 25g-4x 33 34 35 36 -
port-group1/1/10 Eth 10g-4x 37 38 39 40 -
port-group1/1/11 Eth 25g-4x 41 42 43 44 -
port-group1/1/12 Eth 25g-4x 45 46 47 48 -
port-group1/1/13 Eth 40g-2x 49 50 -
port-group1/1/14 Eth 40g-2x 51 52 -
port-group1/1/15 Eth 100g-1x 53 -
port-group1/1/16 Eth 100g-1x 54 -
port-group1/1/17 Eth 100g-1x 55 -
port-group1/1/18 Eth 40g-1x 56 -
Corrección de software
Funcionamiento según lo previsto
Affected Products
PowerSwitch S4112F-ON/S4112T-ON, PowerSwitch S4148F-ON/S4148T-ON/S4148FE-ON, PowerSwitch S4148U-ON, PowerSwitch S5212F-ON, PowerSwitch S5224F-ON, PowerSwitch S5248F-ONArticle Properties
Article Number: 000128222
Article Type: How To
Last Modified: 26 Nov 2025
Version: 8
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.