La porta Dell Networking OS10 S5200 o S4148U non viene visualizzata a causa di un profilo errato del gruppo di porte
Summary: Cavo e ricetrasmettitore sicuramente funzionanti, ma la porta non si accende. Verificato che la porta non è in arresto. Perché la porta non viene visualizzata?
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Instructions
Modelli di switch
S4148U
/S5200
Versione software
OS10
Come modificare la modalità del gruppo di porte
Il gruppo di porte potrebbe non essere configurato per la negoziazione alla velocità specificata.
| Comandi | Descrizione |
|---|---|
show port-group |
Vengono visualizzati tutti i gruppi di porte e la relativa configurazione. |
Annota il numero del gruppo di porte da modificare
. Stiamo cercando la porta 56.
Esempio da S5200:
OS10# show port-group
Port-group Mode Ports FEM
port-group1/1/1 Eth 25g-4x 1 2 3 4 -
port-group1/1/2 Eth 10g-4x 5 6 7 8 -
port-group1/1/3 Eth 10g-4x 9 10 11 12 -
port-group1/1/4 Eth 10g-4x 13 14 15 16 -
port-group1/1/5 Eth 25g-4x 17 18 19 20 -
port-group1/1/6 Eth 25g-4x 21 22 23 24 -
port-group1/1/7 Eth 25g-4x 25 26 27 28 -
port-group1/1/8 Eth 25g-4x 29 30 31 32 -
port-group1/1/9 Eth 25g-4x 33 34 35 36 -
port-group1/1/10 Eth 10g-4x 37 38 39 40 -
port-group1/1/11 Eth 25g-4x 41 42 43 44 -
port-group1/1/12 Eth 25g-4x 45 46 47 48 -
port-group1/1/13 Eth 40g-2x 49 50 -
port-group1/1/14 Eth 40g-2x 51 52 -
port-group1/1/15 Eth 100g-1x 53 -
port-group1/1/16 Eth 100g-1x 54 -
port-group1/1/17 Eth 100g-1x 55 -
port-group1/1/18 Eth 100g-1x 56 -
Esempio da S4148U:
OS10# show port-group Port-group Mode Ports FEM port-group1/1/1 Eth 10g-4x 1 2 3 4 - port-group1/1/2 FC 16g-2x 5 6 7 8 - port-group1/1/3 FC 16g-2x 9 10 11 12 - port-group1/1/4 FC 16g-2x 13 14 15 16 - port-group1/1/5 FC 16g-2x 17 18 19 20 - port-group1/1/6 Eth 10g-4x 21 22 23 24 - port-group1/1/7 Eth 100g-1x 25 - port-group1/1/8 Eth 40g-1x 26 - port-group1/1/9 Eth 100g-1x 29 - port-group1/1/10 Eth 40g-1x 30 -
Esempio:
| Comandi | Descrizione |
|---|---|
OS10# show port-group |
Vengono visualizzati tutti i gruppi di porte e la relativa configurazione. |
OS10(config)# port-group 1/1/18 |
Scegliere la porta che si desidera modificare |
OS10(conf-pg-1/1/18)# mode eth 40g-1x |
Specificare la velocità in cui si desidera impostare la porta. |
Conferma:
<165>1 2019-09-11T23:21:00.470567+00:00 S5248F-ON-U24 dn_ifm 852 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %IFM_ASTATE_UP: Interface admin state up :ethernet1/1/56:1
Verificare che il port-group sia stato modificato:
OS10# show port-group
Port-group Mode Ports FEM
port-group1/1/1 Eth 25g-4x 1 2 3 4 -
port-group1/1/2 Eth 10g-4x 5 6 7 8 -
port-group1/1/3 Eth 10g-4x 9 10 11 12 -
port-group1/1/4 Eth 10g-4x 13 14 15 16 -
port-group1/1/5 Eth 25g-4x 17 18 19 20 -
port-group1/1/6 Eth 25g-4x 21 22 23 24 -
port-group1/1/7 Eth 25g-4x 25 26 27 28 -
port-group1/1/8 Eth 25g-4x 29 30 31 32 -
port-group1/1/9 Eth 25g-4x 33 34 35 36 -
port-group1/1/10 Eth 10g-4x 37 38 39 40 -
port-group1/1/11 Eth 25g-4x 41 42 43 44 -
port-group1/1/12 Eth 25g-4x 45 46 47 48 -
port-group1/1/13 Eth 40g-2x 49 50 -
port-group1/1/14 Eth 40g-2x 51 52 -
port-group1/1/15 Eth 100g-1x 53 -
port-group1/1/16 Eth 100g-1x 54 -
port-group1/1/17 Eth 100g-1x 55 -
port-group1/1/18 Eth 40g-1x 56 -
Correzione software
Funzionamento come previsto
Affected Products
PowerSwitch S4112F-ON/S4112T-ON, PowerSwitch S4148F-ON/S4148T-ON/S4148FE-ON, PowerSwitch S4148U-ON, PowerSwitch S5212F-ON, PowerSwitch S5224F-ON, PowerSwitch S5248F-ONArticle Properties
Article Number: 000128222
Article Type: How To
Last Modified: 26 Nov 2025
Version: 8
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.