Dell Networking OS10 S5200 veya S4148U bağlantı noktası, yanlış bağlantı noktası grubu profili nedeniyle çalışmıyor
Summary: İyi durumda olduğu bilinen kablo ve alıcı-verici ancak bağlantı noktası gelmiyor. Bağlantı noktasının kapalı olmadığı doğrulandı. Liman neden çıkmıyor?
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Instructions
Anahtar Modelleri
S4148U
S5200
Yazılım sürümü
OS10
Bağlantı Noktası Grubu Modu nasıl değiştirilir?
Bağlantı noktası grubu belirtilen hızda anlaşma yapmak için yapılandırılmamış olabilir.
| Komutlar | Açıklama |
|---|---|
show port-group |
Bu, tüm bağlantı noktası gruplarını ve şu anda nasıl yapılandırıldıklarını gösterir. |
Değiştirilecek
bağlantı noktası grubu numarasını not eder Bağlantı noktası 56'yı arıyoruz.
S5200'den örnek:
OS10# show port-group
Port-group Mode Ports FEM
port-group1/1/1 Eth 25g-4x 1 2 3 4 -
port-group1/1/2 Eth 10g-4x 5 6 7 8 -
port-group1/1/3 Eth 10g-4x 9 10 11 12 -
port-group1/1/4 Eth 10g-4x 13 14 15 16 -
port-group1/1/5 Eth 25g-4x 17 18 19 20 -
port-group1/1/6 Eth 25g-4x 21 22 23 24 -
port-group1/1/7 Eth 25g-4x 25 26 27 28 -
port-group1/1/8 Eth 25g-4x 29 30 31 32 -
port-group1/1/9 Eth 25g-4x 33 34 35 36 -
port-group1/1/10 Eth 10g-4x 37 38 39 40 -
port-group1/1/11 Eth 25g-4x 41 42 43 44 -
port-group1/1/12 Eth 25g-4x 45 46 47 48 -
port-group1/1/13 Eth 40g-2x 49 50 -
port-group1/1/14 Eth 40g-2x 51 52 -
port-group1/1/15 Eth 100g-1x 53 -
port-group1/1/16 Eth 100g-1x 54 -
port-group1/1/17 Eth 100g-1x 55 -
port-group1/1/18 Eth 100g-1x 56 -
S4148U'dan örnek:
OS10# show port-group Port-group Mode Ports FEM port-group1/1/1 Eth 10g-4x 1 2 3 4 - port-group1/1/2 FC 16g-2x 5 6 7 8 - port-group1/1/3 FC 16g-2x 9 10 11 12 - port-group1/1/4 FC 16g-2x 13 14 15 16 - port-group1/1/5 FC 16g-2x 17 18 19 20 - port-group1/1/6 Eth 10g-4x 21 22 23 24 - port-group1/1/7 Eth 100g-1x 25 - port-group1/1/8 Eth 40g-1x 26 - port-group1/1/9 Eth 100g-1x 29 - port-group1/1/10 Eth 40g-1x 30 -
Örneğin:
| Komutlar | Açıklama |
|---|---|
OS10# show port-group |
Bu, tüm bağlantı noktası gruplarını ve şu anda nasıl yapılandırıldıklarını gösterir. |
OS10(config)# port-group 1/1/18 |
Değiştirmek istediğiniz bağlantı noktasını seçin |
OS10(conf-pg-1/1/18)# mode eth 40g-1x |
Bağlantı noktasını ayarlamak istediğiniz hızı belirtin |
Onay:
<165>1 2019-09-11T23:21:00.470567+00:00 S5248F-ON-U24 dn_ifm 852 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %IFM_ASTATE_UP: Interface admin state up :ethernet1/1/56:1
Bağlantı noktası grubunun değiştiğini doğrulayın:
OS10# show port-group
Port-group Mode Ports FEM
port-group1/1/1 Eth 25g-4x 1 2 3 4 -
port-group1/1/2 Eth 10g-4x 5 6 7 8 -
port-group1/1/3 Eth 10g-4x 9 10 11 12 -
port-group1/1/4 Eth 10g-4x 13 14 15 16 -
port-group1/1/5 Eth 25g-4x 17 18 19 20 -
port-group1/1/6 Eth 25g-4x 21 22 23 24 -
port-group1/1/7 Eth 25g-4x 25 26 27 28 -
port-group1/1/8 Eth 25g-4x 29 30 31 32 -
port-group1/1/9 Eth 25g-4x 33 34 35 36 -
port-group1/1/10 Eth 10g-4x 37 38 39 40 -
port-group1/1/11 Eth 25g-4x 41 42 43 44 -
port-group1/1/12 Eth 25g-4x 45 46 47 48 -
port-group1/1/13 Eth 40g-2x 49 50 -
port-group1/1/14 Eth 40g-2x 51 52 -
port-group1/1/15 Eth 100g-1x 53 -
port-group1/1/16 Eth 100g-1x 54 -
port-group1/1/17 Eth 100g-1x 55 -
port-group1/1/18 Eth 40g-1x 56 -
Yazılım Düzeltmesi
Tasarlandığı gibi çalışma
Affected Products
PowerSwitch S4112F-ON/S4112T-ON, PowerSwitch S4148F-ON/S4148T-ON/S4148FE-ON, PowerSwitch S4148U-ON, PowerSwitch S5212F-ON, PowerSwitch S5224F-ON, PowerSwitch S5248F-ONArticle Properties
Article Number: 000128222
Article Type: How To
Last Modified: 26 Nov 2025
Version: 8
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.