PowerEdge: M1000e AG 스위치 포트가 영구 비활성화 상태이며 오류: "구성이 가능하지 않습니다."
Summary: PowerEdge M1000e: AG 스위치 포트가 영구 비활성화 상태입니다.
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Symptoms
영향:
F-포트 입력 persistentdisable 상태이며 활성화 상태로 변경할 수 없습니다.
환경:
액세스 게이트웨이 모드
의 DELL PowerEdge M1000e
Brocade M6505문제:
F 포트가 영구 비활성화 상태에서
멈춤Access Gateway를 재부팅한 후 포트가 영구 비활성화 상태로 변경되었습니다.
예:
switchshow : switchName: switchname switchType: 130.0 switchState: Online switchMode: Access Gateway Mode switchWwn: 10:00:00:00:00:00:00:00 switchBeacon: OFF Index Port Address Media Speed State Proto ================================================== <truncated> 6 6 010600 cu N16 In_Sync FC Disabled (Persistent) 7 7 010700 cu N16 Online FC F-Port <pwwn> 8 8 010800 cu N16 In_Sync FC Disabled (Persistent)
로 변경하려고 시도한 후 오류 발생 persistentenabling 포트의:
switchname:admin> portcfgpersistentenable 8 Port 8: portcfgpersistentenable failed. Configuration is not capable(8).
Cause
포트 고착 persistentdisable 구성.
Resolution
절차:
- 수집
ag --mapshow outputF-포트가 어떤 N-포트에 매핑되어 있는지 확인합니다. - 다음 명령을 사용하여 포트를 출고 시 기본값으로 다시 설정합니다.
<portcfgdefault (port no) >에 관한 자세한 내용을 참조하십시오.
예: portCfgDefault 8
- 포트가 다음에서 벗어난 경우 switchshow 명령을 사용하여 포트 상태를 확인합니다.
persistentdisable상태.
예: 이후
portcfgdefault 명령을 실행하면 상태가 다음으로 변경됩니다. In_Sync FC Disabled (No mapping for F-Port)
- 다음 명령을 사용하여 포트를 활성화합니다.
portenable (port no)에 관한 자세한 내용을 참조하십시오. - 다음 명령을 사용하여 포트를 원래 N 포트에 다시 매핑합니다.
ag –mapadd (n-port) (f-port)에 관한 자세한 내용을 참조하십시오.
예:
ag --mapadd 20 "8"
- 다음 명령을 사용하여 포트가 N 포트에 매핑되었는지 확인합니다.
ag --mapshow에 관한 자세한 내용을 참조하십시오. - 다음 명령을 사용하여 포트 상태를 확인합니다.
switchshow에 관한 자세한 내용을 참조하십시오. 포트가 온라인 상태여야 합니다.
예:
Online FC F-Port
Affected Products
Brocade M6505, PowerEdge M1000EArticle Properties
Article Number: 000185988
Article Type: Solution
Last Modified: 12 Jun 2025
Version: 3
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.