Data Domain: Sygnalizator dysku DD3300
Summary: W tym artykule wprowadzono funkcję "sygnału dyskowego" dla systemów DD3300 wprowadzonych z systemem operacyjnym Data Domain (DDOS) 6.2.x. Artykuł bazy wiedzy służy jako przewodnik po tym, jak sygnalizować dysk na DD3300. ...
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Instructions
Podsumowanie:
- W tym artykule wprowadzono funkcję "sygnalizatora dyskowego" dla systemów DD3300. wprowadzone w DDOS 6.2.x.
- Zostaje wydane polecenie "disk beacon 1.n" (przy użyciu SSH/CLI), które powoduje diody LED identyfikacji dysku na odpowiednim dysku.
- Numeracja gniazd fizycznych (na podstawie 0; 1.0) w DD3300 nie jest zgodna z numeracją gniazda DDOS, która zaczyna się od 1.1
- Ta funkcja pomaga w rozwiązywaniu problemów i wymianie uszkodzonych dysków w DD3300.
Dotyczy:
- DD3300 (>= DDOS 6.2.x)
Rozwiązanie:
- Można sygnalizować 12 dysków przednich (1.1> –1.12) lub 1 dysk tylny (1.13).
- 4 dyski wewnętrzne (1.15 -> 1.18) nie obsługują beaconingu.
- Składnia polecenia DD-CLI:
-
disk beacon 1.<slot number> OR <serial number>
-
- Aby zatrzymać naciśnięcie sygnalizatora:
-
Ctrl + C
-
Przykład:
Do gniazda dysku sygnalizatora 1.7:
# disk beacon 1.7
Start disk LED beaconing for 1.7 ...
^C
LED beaconing completed.
#
Aby oznaczyć dysk według numeru seryjnego:
> Zbierz fizyczny numer seryjny sprzętu, wpisując polecenie "disk show hardware detailed".
# disk show hardware detailed
Physical Hardware
Disk Slot Manufacturer/Model Firmware Serial No. Capacity Type State
(pci/idx)
---- --------- ------------------ -------- -------------- ---------- -------- --------
1.1 0 ST4000NM0295 DT31 ZC11Z1GB 3.64 TiB SAS In Use
1.2 1 ST4000NM0295 DT31 ZC1207Y1 3.64 TiB SAS In Use
1.3 2 ST4000NM0295 DT31 ZC12156M 3.64 TiB SAS In Use
1.4 3 ST4000NM0295 DT31 ZC11Z2G6 3.64 TiB SAS In Use
1.5 4 ST4000NM0295 DT31 ZC12108B 3.64 TiB SAS In Use
1.6 5 ST4000NM0295 DT31 ZC120E4S 3.64 TiB SAS In Use
1.7 6 ST4000NM0295 DT31 ZC11Z17L 3.64 TiB SAS In Use
1.8 7 ST4000NM0295 DT31 ZC1207YX 3.64 TiB SAS In Use
1.9 8 ST4000NM0295 DT31 ZC11Z39H 3.64 TiB SAS In Use
1.10 9 ST4000NM0295 DT31 ZC11Z3NW 3.64 TiB SAS In Use
1.11 10 (absent) (absent) (absent) (absent) (absent) Absent
1.12 11 (absent) (absent) (absent) (absent) (absent) Absent
1.13 12 MZ7KM480HMHQ0D3 GD53 S3BUNX0J600149 447.13 GiB SATA-SSD Non-RAID
---- --------- ------------------ -------- -------------- ---------- -------- --------
> Oznacz dysk przy użyciu odpowiedniego numeru seryjnego
# disk beacon ZC11Z17L
Start disk LED beaconing for 1.7 ...
^C
LED beaconing completed.
#
Additional Information
Jeśli sygnalizator dyskowy jest już aktywny na innym dysku (z innej sesji SSH), system wyświetli monit o zatrzymanie aktywnego sygnału nawigacyjnego, jak pokazano poniżej:
# disk beacon 1.13
A beacon command is already running on disk 1.7.
Do you want to terminate it? (yes|no) [yes]: yes
Beacon on disk 1.7 terminated.
Start disk LED beaconing for 1.13 ...
^C
LED beaconing completed.
#
Oryginalna sesja SSH wyświetla następujące dane wyjściowe:
**** Disk beaconing terminated by another disk beacon operation.
Odniesienie:
Mapowanie alertów dysku DD3300 do właściwego gniazda
dysku fizycznegoNiepowodzenie
polecenia sygnalizatora dyskowego DD3300 Opis zachowania diody
LED dysku DD3300 Omówienie sprzętu DD3300 i podręcznik instalacji
Affected Products
Data DomainProducts
Data Domain, DD3300 ApplianceArticle Properties
Article Number: 000013951
Article Type: How To
Last Modified: 29 Sept 2025
Version: 6
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.