PowerFlex: SLES15에서 SDC 서비스 이름이 변경됨

Summary: SLES15에서는 일반적으로 사용되는 서비스 이름 "scini"에서 서비스 이름이 "sdc"로 변경되었습니다.

This article applies to This article does not apply to This article is not tied to any specific product. Not all product versions are identified in this article.

Symptoms

대부분의 PowerFlex 사용자가 사용하는 서비스 이름은 scini입니다.
이러한 변경 사항은 OS(Operating System)와 SDC 드라이버의 상호 작용에 직접적인 영향을 미치기 때문에 사용자는 자동화 기능과 올바른 보고 기능을 사용할 수 없게 됩니다. 전반적인 사용자 환경이 손상되었습니다.
 

Cause

sdc 서비스 이름은 2015년 CoreOS 이후 네이티브 systemd에 사용되었습니다.

2019년에 SLES의 SDC 드라이버는 SysV 및 chkconfig에서 scini 라는 기본 systemd 서비스로 이전되었습니다.

문서 자료 참조는 PowerFlex > 구성 및 맞춤 구성을 참조하십시오. Linux 기반 서버에 SDC를 설치하고 PowerFlex에 연결:
드라이버가 로드되었는지 확인하려면 다음 명령을 사용할 수 있습니다.
o SLES 15:
서비스 SDC 상태
o 기타 모든 Linux 버전:
서비스 scini 상태

Resolution

해결 방법 #1

다른 OS와의 일관성을 위해 드라이버 이름이 sdc 에서 scini로 다시 변경되었으므로 다음 PowerFlex SDC 버전 중 하나 이상으로 업그레이드합니다.

  • PowerFlex SDC v3.5.1.8
  • PowerFlex SDC v3.6.0.6
  • PowerFlex SDC v4.0.100.130

 

해결 방법 #2

여러 이름을 가질 수 있는 서비스인 systemd.unit에 대한 별칭을 만들 수 있습니다.
서비스에 별칭을 추가하려면 [Install] 섹션에서 서비스의 유닛 파일에 줄을 추가해야 합니다. 추가 줄은 빨간색:

scini.service 크랙:
#------------------------------------------------------------------------------
# SDC 서비스 스크립트
# 저자:    에란 보로빅
# 날짜:      2011년 9월 6일
# 버전:   1.1
# 설명: 이 스크립트는 다음과 같은 경우 sdc 서비스를 제어합니다.
# systemd는 init에 사용됩니다.
#------------------------------------------------------------------------------
[단위]
설명=scaleio sdc
이후 = network.target
 
[서비스]
ExecStart=/opt/emc/scaleio/sdc/bin/scini start > /dev/null 2<>/dev/null
ExecStop=/opt/emc/scaleio/sdc/bin/scini stop > /dev/null 2<>/dev/null
재시작초=0
RemainAfterExit=true
 
[설치]
WantedBy=graphical.target 다중 사용자.target [protect2.fireeye.com]별칭=sdc.service

Affected Products

PowerFlex rack, PowerFlex Appliance, PowerFlex custom node, PowerFlex Software
Article Properties
Article Number: 000208293
Article Type: Solution
Last Modified: 20 Nov 2025
Version:  8
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.