Skip to main content
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Create and access a list of your products

Procedura per ripristinare la configurazione predefinita di fabbrica di S50N/V

This article applies to This article does not apply to This article is not tied to any specific product. Not all product versions are identified in this article.

Instructions

Per ripristinare le impostazioni predefinite di S50, attenersi alle istruzioni riportate di seguito.
  1. Collegarsi a un dispositivo S50N/V tramite console
    • Velocità in baud = 9.600
    • Dimensione carattere = 8
    • Controllo di flusso = Disattivato
    • Bit di stop = 1
    • Parità = Nessuna
  2. Spegnere e riaccendere S50 scollegando e ricollegando il cavo di alimentazione oppure digitando reload, quindi yes in modalità exec con privilegi
    • FTOS#reload
  3. Premere un tasto qualsiasi quando richiesto durante il processo di avvio di S50 per entrare in modalità BOOT_USER
U-Boot 1.1.4 (F10 Development) (Oct 6 2009 - 03:14:26)
Built by build at hydrogen on Tue Oct 6 3:14:25 2009
S-Series Boot selector Label 2.8.2.0

CPU: 8541, Version: 1.1, (0x807a0011)
Core: E500, Version: 2.0, (0x80200020)
Clock Configuration:
       CPU: 660 MHz, CCB: 330 MHz,
       DDR: 165 MHz, LBC: 41 MHz
L1: D cache 32 kB enabled
       I-cache 32 kB enabled
Board: S50 Force10 Networks
       Watchdog enabled
DRAM: Initializing
    DDR: 256 MB
Top of RAM usable for U-Boot at: 10000000
Reserving 122k for U-Boot at: 0ffe0000
Reserving 136k for malloc() at: 0ffbe000
Reserving 76 Bytes for Board Info at: 0ffbdfb4
Reserving 72 Bytes for Global Data at: 0ffbdf6c
Stack Pointer at: 0ffbdf48
New Stack Pointer is: 0ffbdf48
Now running in RAM - U-Boot at: 0ffe0000
L2 cache 256KB: enabled
Using default environment

PCI Scan: Found Bus 0, Device 22, Function 0
PCI Scan: Found Bus 0, Device 23, Function 0

In: serial
Out: serial
Err: serial
U-Boot relocated to 0ffe0000
Net: No ethernet found.
### main_loop entered: bootdelay=1

### main_loop: bootcmd="bootm 0xffe80000;setenv verify no;autoscr 0x1700000
bootm fe6000f0"
Hit any key to stop booting: 0
## Booting image at ffe80000 ...
   Image Name: netbsd
   Image Type: PowerPC NetBSD Standalone Program (uncompressed)
   Data Size: 383216 Bytes = 374.2 kB
   Load Address: 00040000
   Entry Point: 00040004
   Verifying Checksum ... OK
   Watchdog Disabled
   Loading Standalone Application ... OK
Unit 0
Unit 1
Registering ethernet driver for unit 0
Registering ethernet driver for unit 1

None of the boot parameters are configured!!
So Booting from flash!!

You can use U-boot native networking facilities
============================================================



Hit any key to break into BOOT_USER mode: 0 < ------------- hit any key
Starting F10 BLI Shell ...
BOOT_USER #

4. Inserire il comando "restore factory-defaults" nella finestra BOOT_USER

BOOT_USER #restore factory-defaults

Erasing NVRAM contents...
Successfully erased NVRAM contents
Erasing Filesystem sectors...

Successfully erased filesystem sectors
Erasing boot parameters...
Successfully erased boot parameters
Please reload for restore factory-defaults to take effect.

5. Inserire il comando "reload" per l'esecuzione e il sistema S50N/V si avvierà con la configurazione predefinita di fabbrica (non è necessario premere alcun tasto durante questo processo di avvio)

BOOT_USER #reload
!
!
Force10>
Force10>en
Force10#00:07:00: %STKUNIT0-M:CP %SEC-4-ENABLE_PASSW_NOT_CONFIGURED: Enable password is required for authentication but not configured
00:07:00: %STKUNIT0-M:CP %SEC-3-AUTHENTICATION_ENABLE_SUCCESS: Enable password authentication success  on console

 
6. Lo switch è ora impostato con la configurazione predefinita di fabbrica e può essere configurato da qui

Force10#config t
Force10(conf)#
 
Article Properties
Article Number: 000122552
Article Type: How To
Last Modified: 21 Feb 2021
Version:  3
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.