Skip to main content
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Create and access a list of your products

Procedur för att ställa in S50N/V till standardkonfigurationen från fabrik

This article applies to This article does not apply to This article is not tied to any specific product. Not all product versions are identified in this article.

Instructions

Om du vill återställa S50 till fabriksinställningarna följer du följande anvisningar.
  1. Anslut till S50N/V-enhet via konsol
    • Överföringshastighet = 9600
    • Teckenstorlek = 8
    • Flödeskontroll = Avaktiverad
    • Stoppbitar: 1
    • Paritet = ingen​
  2. Starta om S50 genom att antingen dra ut och koppla in nätsladden igen eller genom att skriva reload och sedan yes i privilegierat körningsläge
    • FTOS#reload
  3. Tryck på valfri knapp när du blir ombedd under S50-startprocessen för att gå in i BOOT_USER-läge
U-Boot 1.1.4 (F10 Development) (6 okt 2009 – 03:14:26)
Built by build at hydrogen on Tue Oct  6  3:14:25 2009
S-Series Boot selector Label 2.8.2.0

CPU:   8541, Version: 1.1, (0x807a0011)
Core:  E500, Version: 2.0, (0x80200020)
Clock Configuration:
       CPU: 660 MHz, CCB: 330 MHz,
       DDR: 165 MHz, LBC:  41 MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled
Board: S50 Force10 Networks
       Watchdog enabled
DRAM:  Initializing
    DDR: 256 MB
Top of RAM usable for U-Boot at: 10000000
Reserving 122k for U-Boot at: 0ffe0000
Reserving 136k for malloc() at: 0ffbe000
Reserving 76 Bytes for Board Info at: 0ffbdfb4
Reserving 72 Bytes for Global Data at: 0ffbdf6c
Stack Pointer at: 0ffbdf48
New Stack Pointer is: 0ffbdf48
Now running in RAM - U-Boot at: 0ffe0000
L2 cache 256KB: enabled
Using default environment

PCI Scan: Found Bus 0, Device 22, Function 0
PCI Scan: Found Bus 0, Device 23, Function 0

In:    serial
Out:   serial
Err:   serial
U-Boot relocated to 0ffe0000
Net:   No ethernet found.
### main_loop entered: bootdelay=1

### main_loop: bootcmd="bootm 0xffe80000;setenv verify no;autoscr 0x1700000
bootm fe6000f0"
Tryck på valfri tangent för att stoppa uppstart: 0
## Booting image at ffe80000 ...
   Image Name:   netbsd
   Image Type:   PowerPC NetBSD Standalone Program (uncompressed)
   Data Size:    383216 Bytes = 374.2 kB
   Load Address: 00040000
   Entry Point:  00040004
   Verifying Checksum ... OK
   Watchdog Disabled
   Loading Standalone Application ... OK
Unit 0
Unit 1
Registering ethernet driver for unit 0
Registering ethernet driver for unit 1

None of the boot parameters are configured!!
So Booting from flash!!

You can use U-boot native networking facilities
============================================================



Hit any key to break into BOOT_USER mode:  0 < ------------- hit any key
Starting F10 BLI Shell ...
BOOT_USER #

4. Ange kommandot ”restore factory-defaults” i kommandotolken BOOT_USER

BOOT_USER #restore factory-defaults

Erasing NVRAM contents...
Successfully erased NVRAM contents
Erasing Filesystem sectors...

Successfully erased filesystem sectors
Erasing boot parameters...
Successfully erased boot parameters
Please reload for restore factory-defaults to take effect.

5. Ange kommandot ”reload” för att köra och S50N/V-systemet startar med fabriksinställningar (du behöver inte trycka på någon tangent under uppstartsproceduren)

BOOT_USER #reload
!
!
Force10>
Force10>en
Force10#00:07:00: %STKUNIT0-M:CP %SEC-4-ENABLE_PASSW_NOT_CONFIGURED: Enable password is required for authentication but not configured
00:07:00: %STKUNIT0-M:CP %SEC-3-AUTHENTICATION_ENABLE_SUCCESS: Enable password authentication success  on console

 
6. Switchen är nu fabriksåterställd och kan konfigureras

Force10#config t
Force10(conf)#
 
Article Properties
Article Number: 000122552
Article Type: How To
Last Modified: 21 Feb 2021
Version:  3
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.