PowerFlex: SDS 분리 네트워크 테스트
Summary: 이 문서에서는 MDM 서버에서 수신한 SDS_Decoupled 오류를 해결하는 방법을 설명합니다.
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Symptoms
SDS 연결 해제는 다음과 같은 증상으로 나타납니다.
- 스토리지 재구축/재조정
- 스페어 용량 감소
- 나머지 SDS 시스템의 디스크 사용량 증가
- 볼륨이 손상되었을 수 있음
- 디바이스의 긴 IO 또는 디바이스 문제
MDM 이벤트 로그에서 다음 오류를 찾습니다.
7256 2017-07-13 14:20:12.410 SDS_DECOUPLED ERROR SDS: SDS_10.241.xxx.xxx (id: 3711776c00000003) decoupled.
Cause
MDM과의 통신을 위한 keep-alive 시간 초과는 5초입니다. MDM 연결 해제와 마찬가지로 네트워크 레이턴시 및 프로세스 문제를 확인합니다.
Resolution
scli query_all_sds를 수행하면 연결 끊기 메시지가 표시될 수 있습니다.
MDM과 SDS 노드 간의 연결을 확인합니다.
SDS에서 통신할 수 없다고 표시하는 연결의 경우 호스트 간에 텔넷을 포트 7072로 실행합니다. 연결할 수 없는 경우 타겟 서버에서 SDS 프로세스가 실행되고 있는지 확인하십시오. 방화벽이나 차단할 수 있는 다른 항목이 있는지 네트워크와 호스트를 확인하십시오.
scli --start_sds_network_test
를 사용하여 결과를 검색합니다.
scli --query_sds_network_test --sds_ip 10.241.xxx.xxx SDS with IP 10.241.xxx.xxx (port 7072) returned information on 4 SDSs SDS 3711505b00000000 10.xxx.xxx.xxx bandwidth 183.8 MB (188254 KB) per-second SDS 3711505c00000001 10.xxx.xxx.xxx bandwidth 182.9 MB (187245 KB) per-second SDS 3711505d00000002 10.xxx.xxx.xxx bandwidth 182.2 MB (186579 KB) per-second SDS 3711776d00000004 10.xxx.xxx.xxx bandwidth 174.7 MB (178937 KB) per-second
이것이 문제인지 확인하려면 각 SDC에서 포트 7072에 대한 텔넷 세션을 실행합니다. 거부가 표시되면 네트워크 연결을 확인합니다. 다음은 올바른 출력입니다.
[root@scaleio-1 ~]# telnet 10.xxx.xxx.xxx 7072 Trying 10.xxx.xxx.xxx... Connected to 10.xxx.xxx.xxx. Escape character is '^]'.
다음은 실패한 연결의 예입니다.
[root@scaleio-1 ~]# telnet 10.xxx.xxx.xxx 7072 Trying 10.xxx.xxx.xxx... telnet: connect to address 10.xxx.xxx.xxx: No route to host
Affected Products
VxFlex Product FamilyProducts
VxFlex Product FamilyArticle Properties
Article Number: 000064157
Article Type: Solution
Last Modified: 04 Sep 2025
Version: 4
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.