[Isilon] 재부팅 후 Gen6 노드가 클러스터에서 분리

Summary: 클러스터의 Gen6 노드는 노드가 BMC와 통신할 수 없고 노드가 RO 상태로 표시될 수 있는 이벤트를 로깅합니다. 노드를 재부팅하면 노드가 클러스터에서 분리됩니다.

This article applies to This article does not apply to This article is not tied to any specific product. Not all product versions are identified in this article.
Check out other resources

Symptoms

클러스터에서 isi 이벤트에 다음 오류가 표시될 수 있습니다.

14.99844  03/14 13:38 C    17   203764         The Baseboard Management Controller (BMC) located in chassis xxxxxxxxxxx, slot 4 is not responding. This controller monitors hardware components such as batteries and power supplies. To ensure these hardware components continue to be monitored, service the BMC as soon as possible.


직렬 연결이 있는 노드의 재부팅을 시도하는 경우 ePOST 출력에서 다음이 관찰됩니다.

Copyright (c) EMC Corporation , 2021
Disk Array Subsystem Controller
Model: Infinity Banshee: Isilon
DiagName: Extended POST
DiagRev: Rev 28.15
Build Date: Mon May 17 22:52:58 2021
BiosRev: 37.41
UEFIFWVolRev: Rev 03.43
FixedSERDESRev: Rev 08.00
BMCMainAppRev: 00.00
BMCSSPRev: 00.00
BMCEMCBBRev: 00.00
StartTime: 03/10/2022 22:10:45
SaSerialNo:


ABCDabcEaFaGHIabJabcKabcdefLabcdefMabcdefNOabPabcQRS
SPI_Buffer_Mgmt::Initialize(): Could not read NVRAM mem persistence struct
TUVWXYZAABBCCabDDabEEabFFabGGHHIIJJKKLLMMNNabOOPPabcQQRRSSTTUUVVWWXXYYZZAAABBBCCCDDD

************************************************************
*                 Extended POST Messages
************************************************************

WARNING:Failed to set fault/status code value:0x01000000 (offset:0x02A8)
INFORMATION:POST Start
WARNING:INIT: IPMI Error Reading Chassis Resume PROM (0x03E0)
WARNING:INIT: IPMI Error Reading SP Resume PROM (0x03E0)
WARNING:Failed to read Boot Options structure from Virtual EEPROM (0x03E0)
WARNING:FRU capability Register in SP resume is not set correctly, VRD components are not recognized
WARNING:Error reading SLIC status sensor or sensor scanning could be disabled for HBA0 card (0x03E0)
WARNING:Error reading SLIC status sensor or sensor scanning could be disabled for HBA1 card (0x03E0)
WARNING:Error reading SLIC status sensor or sensor scanning could be disabled for Disk Interface Card (0x03E0)
WARNING:Unable to read VEEPROM Shared Data Region (0x03E0)
WARNING:Failed to read Boot Options structure from Virtual EEPROM (0x03E0)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Couldn't read Chassis Status
WARNING:Couldn't read sensor or sensor scanning could be disabled (0x90)
WARNING:Couldn't read sensor or sensor scanning could be disabled (0x98)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Couldn't read CMD Sequencer board ID (0x03E0)
WARNING:CMD Sequencer: Failed to read Board ID. No +/-6CMD tolerance applied (BMC code: 0x00)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000025 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000026 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000027 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000003 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x0100002B (offset:0x02A8)
WARNING:Couldn't read Infinity DIB CMD board ID (0x03E0)
WARNING:Infinity DIB CMD: Failed to read Board ID. No +/-6CMD tolerance applied (BMC code: 0x00)
WARNING:Failed to set fault/status code value:0x01000015 (offset:0x02A8)
WARNING:PSA not present
WARNING:Failed to set fault/status code value:0x01000016 (offset:0x02A8)
WARNING:PSB not present
WARNING:Failed to set fault/status code value:0x01000017 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000025 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000025 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000026 (offset:0x02A8)
WARNING:M.2 SATA 0 FW FileSystem Inaccessible (0x00FF)
WARNING:Failed to set fault/status code value:0x01000027 (offset:0x02A8)
WARNING:Firmware Update Skipped Due To PSA Status
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x0100002B (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x0100002B (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x0100002B (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000002 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000015 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000016 (offset:0x02A8)
WARNING:Failed to set fault/status code value:0x01000017 (offset:0x02A8)
************************************************************


EndTime: 03/10/2022 22:10:58


.... Storage System Failure - Contact your Service Representative ...


ErrorCode: 0x000003E0
ErrorDesc:
FRU: Motherboard
Device: BMC
Description: IPMI Transport Protocol Not Found Error!
Rev: 28.15
Send_IPMI_CMD()
Failed to get BMC self test results
Self Test Results*
P/N:
S/N:
EndError:
ErrorTime: 03/10/2022 22:10:45


ErrorCode: 0x000003EA
ErrorDesc:
FRU: Motherboard
Device: NVRAM
Description: NVRAM IPMI Protocol Not Found Error!
Rev: 28.15
EMC NVRAM IPMI Protocol not found!
Initialize NVRAM*
P/N:
S/N:
EndError:
ErrorTime: 03/10/2022 22:10:45


ErrorCode: 0x000001BB
ErrorDesc:
FRU: Motherboard
Device: CMOS Bank 1
Description: BIOS SMI Handler is disabled Error!
Rev: 28.15
CMOS Init*
P/N:
S/N:
EndError:
ErrorTime: 03/10/2022 22:10:45


ErrorCode: 0x000003E0
ErrorDesc:
FRU: Motherboard
Device: LAN Management Port
Description: IPMI Transport Protocol Not Found Error!
Rev: 28.15
Send_IPMI_CMD()
Failed to get/verify BMC MAC address
Verify-Set BMC MAC Addr*
P/N:
S/N:
EndError:
ErrorTime: 03/10/2022 22:10:46


ErrorCode: 0x000003E0
ErrorDesc:
FRU: Motherboard
Device: BIOS ROM
Description: IPMI Transport Protocol Not Found Error!
Rev: 28.15
Send_IPMI_CMD()
Failed to set SSP power reset request(code: 0x01)
EndError:
ErrorTime: 03/10/2022 22:10:57


ErrorCode: 0x000003E0
ErrorDesc:
FRU: Motherboard
Device: M.2 SATA 1
Description: IPMI Transport Protocol Not Found Error!
Rev: 28.15
Send_IPMI_CMD()
Failed to get sensor reading
Sensor ID: 0x90
EndError:
ErrorTime: 03/10/2022 22:10:53



EMC Extended POST End: 03/10/2022 22:11:08


노드가 계속 부팅되지만 마지막에는 다음과 같은 메시지가 나타납니다.
 

Secondary backup method None is unknown
None backup is invalid.
Initializing with a new backup of current data.
Secondary backup method None is unknown
None backup does not exist.
Installation config method is PSF: Pulling PSI config files from backup
Secondary backup method None is unknown
Unable to pull files from None backup
Installation config method is PSF: Unable to pull secondary backup files
Installation config method is PSF: Copying PSI config files
PSF file path /mfg/psi/psf.json does not exist in primary backup

Failed to copy PSI config files: Chassis is missing a PSI receipt.
A receipt must be provided before the boot will be allowed to continue.
To prevent a DL situation, contact Dell EMC Customer Support immediately:
United States: 1 800 782 4362 (1 800 SVC 4EMC)
Canada: 1 800 543 4782 (1 800 543 4SVC)
Worldwide Country Code: 1 508 497 7901


Command Options:
1) Enter recovery shell
2) Continue booting
3) Reboot
option>

 

Cause

1GbE 네트워크의 UDP 스톰으로 인해 노드의 BMC가 응답을 중지했습니다. 

이 문제는 Gen6(A200/A2000/H400/H500/H600/H5600/F800/F810)에만 적용됩니다. PowerScale 또는 PowerScale 하이브리드 노드에는 영향을 주지 않습니다.

Resolution

해결 방법:
  1. 영향을 받는 노드에서 1GbE 인터페이스를 뽑습니다.
  2. 복구 셸을 입력합니다.
  3. 노드를 재부팅합니다.
문제 해결:
NFP(Node Firmware Package) 11.6 이상 버전을 적용합니다.

Affected Products

Isilon A200, Isilon A2000, Isilon F800, Isilon F810, Isilon Gen6, Isilon H400, Isilon H500, Isilon H5600, Isilon H600
Article Properties
Article Number: 000213534
Article Type: Solution
Last Modified: 08 Sept 2023
Version:  2
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.