ECS: Så här identifierar du modellen för en SPF som är ansluten till ett nodnätverksgränssnitt. Så här får du komponentnumret för en Dell SFP/kabel.
Summary: Det är ofta svårt att identifiera vilken typ av kabel eller SFP (Small Form-Factor Pluggable) som används i en miljö för att diagnostisera ett problem.
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Instructions
Så här identifierar du en SFP-typ och modell som är ansluten till en ECS-nod.
Nätverksgränssnitt som använder en SFP kan vara klientdelsgränssnitt slave-0 och slave-1 på generation 1 eller 2. Frontend-gränssnitt slave-0, slave-1 och backend-gränssnittpslave-0, pslave-1 på Gen 3
Kommando:
# sudo ethtool -m <nätverksgränssnitt>
Exempel: (Kopparanslutning)
admin@node1:~> sudo ethtool -m slave-0
Identifier : 0x03 (SFP)
Extended identifier : 0x04 (GBIC/SFP defined by 2- wire interface ID)
Connector : 0x23 (No separable connector)
Transceiver codes : 0x01 0x00 0x00 0x00 0x00 0x04 0x80 0xf5
Transceiver type : Infiniband: 1X Copper Passive
Transceiver type : Passive Cable
Transceiver type : FC: Twin Axial Pair (TW)
Transceiver type : FC: 1200 MBytes/sec
Transceiver type : FC: 800 MBytes/sec
Transceiver type : FC: 400 MBytes/sec
Transceiver type : FC: 200 MBytes/sec
Transceiver type : FC: 100 MBytes/sec
Encoding : 0x06 (64B/66B)
BR, Nominal : 25500MBd
Rate identifier : 0x00 (unspecified)
Length (SMF,km) : 0km
Length (SMF) : 0m
Length (50um) : 0m
Length (62.5um) : 0m
Length (Copper) : 2m
Length (OM3) : 0m
Passive Cu cmplnce. : 0x01 (SFF-8431 appendix E) [SFF-8472 rev10.4 only]
Vendor name : DELL
Vendor OUI : 3c:18:a0
Vendor PN : D0R73
Vendor rev : A0
Option values : 0x00 0x00
BR margin, max : 103%
BR margin, min : 0%
Vendor SN : CN0LXD0093517LL
Date code : 190305
Optical diagnostics support : No
Exempel: (Optisk)
admin@node1:~> sudo ethtool -m slave-0
Identifier : 0x03 (SFP)
Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID)
Connector : 0x07 (LC)
Transceiver codes : 0x10 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Transceiver type : 10G Ethernet: 10G Base-SR
Encoding : 0x06 (64B/66B)
BR, Nominal : 10300MBd
Rate identifier : 0x00 (unspecified)
Length (SMF,km) : 0km
Length (SMF) : 0m
Length (50um) : 80m
Length (62.5um) : 30m
Length (Copper) : 0m
Length (OM3) : 300m
Laser wavelength : 850nm
Vendor name : DELL
Vendor OUI : 00:17:6a
Vendor PN : WTRD1
Vendor rev : A0
Option values : 0x00 0x1a
Option : RX_LOS implemented
Option : TX_FAULT implemented
Option : TX_DISABLE implemented
BR margin, max : 0%
BR margin, min : 0%
Vendor SN : AD858A01EJ
Date code : 180510
Optical diagnostics support : Yes
Laser bias current : 6.520 mA
Laser output power : 0.5716 mW / -2.43 dBm
Receiver signal average optical power : 0.3608 mW / -4.43 dBm
Module temperature : 44.32 degrees C / 111.78 degrees F
Module voltage : 3.3291 V
Alarm/warning flags implemented : Yes
Laser bias current high alarm : Off
Laser bias current low alarm : Off
Laser bias current high warning : Off
Laser bias current low warning : Off
Laser output power high alarm : Off
Laser output power low alarm : Off
Laser output power high warning : Off
Laser output power low warning : Off
Module temperature high alarm : Off
Module temperature low alarm : Off
Module temperature high warning : Off
Module temperature low warning : Off
Module voltage high alarm : Off
Module voltage low alarm : Off
Module voltage high warning : Off
Module voltage low warning : Off
Laser rx power high alarm : Off
Laser rx power low alarm : Off
Laser rx power high warning : Off
Laser rx power low warning : Off
Laser bias current high alarm threshold : 10.500 mA
Laser bias current low alarm threshold : 2.500 mA
Laser bias current high warning threshold : 10.500 mA
Laser bias current low warning threshold : 2.500 mA
Laser output power high alarm threshold : 2.0000 mW / 3.01 dBm
Laser output power low alarm threshold : 0.1260 mW / -9.00 dBm
Laser output power high warning threshold : 0.7900 mW / -1.02 dBm
Laser output power low warning threshold : 0.3170 mW / -4.99 dBm
Module temperature high alarm threshold : 85.00 degrees C / 185.00 degrees F
Module temperature low alarm threshold : -5.00 degrees C / 23.00 degrees F
Module temperature high warning threshold : 80.00 degrees C / 176.00 degrees F
Module temperature low warning threshold : 0.00 degrees C / 32.00 degrees F
Module voltage high alarm threshold : 3.6000 V
Module voltage low alarm threshold : 3.0000 V
Module voltage high warning threshold : 3.4600 V
Module voltage low warning threshold : 3.1300 V
Laser rx power high alarm threshold : 2.0000 mW / 3.01 dBm
Laser rx power low alarm threshold : 0.0315 mW / -15.02 dBm
Laser rx power high warning threshold : 0.7900 mW / -1.02 dBm
Laser rx power low warning threshold : 0.0315 mW / -15.02 dBm
Utdata ovan kan hjälpa dig att identifiera artikelnummer, leverantör och mer information om de gränssnitt som granskas.
Additional Information
Information om liknande information för en Gen 3-switch finns i ECS: Så här identifierar du SFP-komponentnumret på en Gen 3-switch.
Affected Products
ECS ApplianceProducts
ECS ApplianceArticle Properties
Article Number: 000021756
Article Type: How To
Last Modified: 24 Sept 2025
Version: 5
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.