如何在适用于戴尔阵列的 Microsoft MPIO 中配置所有必需的设备 ID
Summary: 如何在戴尔阵列的 Microsoft 多路径 I/O （MPIO） 中配置所有必需的设备 ID。
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Instructions
在使用下面所示的任何方法之前，必须安装或启用 Microsoft Windows MPIO 功能。
只需为您的系统添加适当的条目。
使用 MPIO 控制面板小程序
- 打开 MPIO 控制面板小程序。
- 转至 MPIO-ed Devices选项卡，其中显示由 MPIO 管理的设备的硬件 ID（如果存在）。
- 检查是否存在 EMC、DGC、COMPELNT 或戴尔供应商阵列类型，如下面的列表所示，其中添加了相应的磁盘类型。
- 如果没有，则单击 Add ，然后在 DGC 设备下添加阵列类型，后跟五个空格，使其总共八个字符（包括空格）。然后在硬件 ID 下添加硬件。示例：RAID 10、RAID 5 或 VRAID，后跟空格，使其总共为 16 个字符。然后，单击“ 确定 ”并重新启动服务器。
- 以下是采用供应商 8 和产品 16 格式在 MPIO 中添加此类设备的示例：
Add DGC followed by 5 blank spaces, then RAID 0 followed by 10 blank spaces. Click OK. Add DGC followed by 5 blank spaces, then RAID 1 followed by 10 blank spaces. Click OK. Add DGC followed by 5 blank spaces, then RAID 3 followed by 10 blank spaces. Click OK. Add DGC followed by 5 blank spaces, then RAID 10 followed by 9 blank spaces. Click OK. Add DGC followed by 5 blank spaces, then RAID 5 followed by 10 blank spaces. Click OK. Add DGC followed by 5 blank spaces, then VRAID followed by 11 blank spaces. Click OK. Add DGC followed by 5 blank spaces, then DISK followed by 12 blank spaces. Click OK. Add DGC followed by 5 blank spaces, then VNX followed by 13 blank spaces. Click OK. Add EMC followed by 5 blank spaces, then Celerra followed by 9 blank spaces. Click OK. Add EMC followed by 5 blank spaces, then VPLEX followed by 11 blank spaces. Click OK. Add EMC followed by 5 blank spaces, then Invista followed by 9 blank spaces. Click OK. Add EMC followed by 5 blank spaces, then SYMMETRIX followed by 7 blank spaces. Click OK. Add XtremIO followed by 1 blank space, then XtremApp followed by 8 blank spaces. Click OK. Add COMPELNT followed by 0 blank spaces, then Compellent followed by 6 blank spaces. Click OK. Add DellEMC followed by 1 blank space, then by PowerStore followed by 6 blank spaces. Click OK.
- 添加相关设备 ID 后，重新启动服务器。
使用 MPCLAIM
打开提升的命令提示符（即以管理员身份运行）。
提醒：引号中的字符串必须由两个特定长度的字符串组成。
供应商 ID 右侧用空格填充，长度为 8 个字符，紧跟产品 ID 右侧用空格填充，长度为 16 个字符，总长度为 24 个字符。
mpclaim.exe -r i d "DGC RAID 0 " mpclaim.exe -r i d "DGC RAID 1 " mpclaim.exe -r i d "DGC RAID 3 " mpclaim.exe -r i d "DGC RAID 10 " mpclaim.exe -r i d "DGC RAID 5 " mpclaim.exe -r i d "DGC VRAID " mpclaim.exe -r i d "DGC DISK " mpclaim.exe -r i d "DGC VNX " mpclaim.exe -r i d "EMC Celerra " mpclaim.exe -r i d "EMC VPLEX " mpclaim.exe -r i d "EMC Invista " mpclaim.exe -r i d "EMC SYMMETRIX " mpclaim.exe -r i d "XtremIO XtremApp " mpclaim.exe -r i d "COMPELNTCompellent " mpclaim.exe -r i d "DellEMC PowerStore "
使用 PowerShell
上述替代方法是使用 PowerShell 命令添加设备 ID。
打开提升的 PowerShell 窗口（即以管理员身份运行）。
使用 PowerShell 命令时，VendorID 和 ProductID 不必用空格填充。
New-MSDSMSupportedHW -VendorId "DGC" -ProductId "RAID 0" New-MSDSMSupportedHW -VendorId "DGC" -ProductId "RAID 1" New-MSDSMSupportedHW -VendorId "DGC" -ProductId "RAID 3" New-MSDSMSupportedHW -VendorId "DGC" -ProductId "RAID 10" New-MSDSMSupportedHW -VendorId "DGC" -ProductId "RAID 5" New-MSDSMSupportedHW -VendorId "DGC" -ProductId "VRAID" New-MSDSMSupportedHW -VendorId "DGC" -ProductId "DISK" New-MSDSMSupportedHW -VendorId "DGC" -ProductId "VNX" New-MSDSMSupportedHW -VendorId "EMC" -ProductId "Celerra" New-MSDSMSupportedHW -VendorId "EMC" -ProductId "VPLEX" New-MSDSMSupportedHW -VendorId "EMC" -ProductId "Invista" New-MSDSMSupportedHW -VendorId "EMC" -ProductId "SYMMETRIX" New-MSDSMSupportedHW -VendorId "XtremIO" -ProductId "XtremApp" New-MSDSMSupportedHW -VendorId "COMPELNT" -ProductId "Compellent" New-MSDSMSupportedHW -VendorId "DellEMC" -ProductId "PowerStore"
Affected Products
PowerPath for WindowsProducts
PowerPath for WindowsArticle Properties
Article Number: 000021038
Article Type: How To
Last Modified: 28 Oct 2025
Version: 9
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.