Dell Unity：升级前运行状况检查失败，并显示错误：Check_connectemc_sender_1

Summary: 升级前运行状况检查 （PUHC） 失败，并显示错误：ERROR_CODE=platform：：check_connectemc_sender_1|错误|升级无法继续（戴尔可纠正）

This article applies to This article does not apply to This article is not tied to any specific product. Not all product versions are identified in this article.
Check out other resources

Symptoms

升级前运行状况检查 （PUHC） 失败，并显示错误： 
ERROR_CODE=platform::check_connectemc_sender_1|Error|
UPGRADE CANNOT PROCEED.
check_connectemc_sender_1
errors :0x1000300- Operation failed. Error code: 0x1000300 The requested object could not be found on the system. Recheck the command name. 0x6400bee - Failed to perform the operation because connect home has not been configured

Cause

提醒：从 Unity OE 5.3 开始， ConnectHome 连接通知使用 <serialNumber>@dell.com 不再是默认值。


配置 ConnectHome 连接时，请包括来自系统域名的电子邮件地址或通过 SMTP 服务器身份验证的适用电子邮件地址。

为了在 5.3 及更高版本中启用 SupportAssist，ConnectEMC 必须具有“发件人”电子邮件地址。

Resolution

有两个选项可以解决此问题。

  1. 跳过 PUHC 并执行升级。稍后添加发件人电子邮件地址。
  2. 立即添加发件人电子邮件地址，然后执行升级。


选项 1：跳过 PUHC 并执行升级

  1. 运行 以下命令：
svc_skip_puhc
  1. 运行 以下命令以跳过错误：
+58

50: flr::check_for_disk_transitions
51: flr::check_for_faulted_disks
52: flr::check_for_no_pulled_disks
53: flr::check_for_snaps_in_an_active_state
54: flr::check_movesession_exists
55: slic::check_for_slic_committed
56: platform::check_centralized_esrs_version
57: platform::check_unsupported_proxy
58: platform::check_connectemc_sender
  1. 一旦 check_connectemc_sender 跳过，则从 Unisphere 开始升级 。
  2. 添加以下项的发件人电子邮件地址 ： ConnectEMC。（见下文）


选项 2：添加发件人电子邮件地址，然后升级

有三个选项可用于添加发件人电子邮件地址：

  1. Unisphere
  2. svc_connectemc 命令
  3. Uemcli 命令

Unisphere：

SMTP

svc_connectemc：

  1. 运行 以下命令以显示 ConnectEMC 地位：
svc_connectemc -s

ConnectEMC: NOTRUNNING DISABLE
  1. 测试 ConnectEMC 要使用以下命令向支持部门发送消息，请执行以下作：
spa:/cores/service/user# svc_connectemc -t

ERROR [spa]: Email (ConnectEMC) not configured
  1. 运行 以下命令以显示 ConnectEMC 配置详细信息：
svc_connectemc -g

INFO [spa]: SMTP Host: smtp.server.com
INFO [spa]: SENDER EMAIL: DP-Unity01@dell.com
INFO [spa]: EMC Destination Email: emailalert@emc.com
  1. 运行 以下命令以设置电子邮件地址 ConnectEMC 用于发送警报：
05:57:12 root@CKM002XXXXX929 spa:/cores/service/user# svc_connectemc -m DP-Unity01@dell.com

INFO [spa]: Verifying peer connectivity ...
ERROR [spa]: Email (ConnectEMC) not configured. Please enable connetEMC first.
  1. 运行 以下命令以启用 ConnectEMC：
05:58:30 root@CKM002XXXXX929 spa:/cores/service/user# svc_connectemc --enable 10.1XX.1XX.1X1 --sendermail DP-Unity01@dell.com

INFO [spa]: Verifying peer connectivity ...
INFO [spa]: Enabling ConnectEMC
INFO [spa]: Verifying peer connectivity ...
INFO [spa]: copying connectEMC config to peer
INFO [spa]: Persisting SMTP server configuration
INFO [spa]: Persisting sender email address configuration
INFO [spa]: ConnectEMC has been enabled successfully.
  1. 启用后 ConnectEMC， 测试连接：  
    svc_connectemc -t
INFO [spa]: Test Dialhome request

Uemcli：

  1. 运行 以下命令以列出当前配置：
uemcli /sys/support/connecthome show -detail

1:  Enabled       = yes
   SMTP server     = 10.1XX.1XX.1X1
   E-mail from address = (none)@emc.com 
   E-mail to address  = emailalert@emc.com
启用之前 ConnectEMC，如果验证测试命令，则会失败并显示错误：  
Operation failed. Error code: 0x1000300
The requested object could not be found on the system. Recheck the command name. (Error Code:0x1000300)
  1. 运行 以下命令以启用 ConnectEMC： 
uemcli -d 10.0.0.1 -u local/joe -p Password /sys/support/connecthome set –enable yes –smtpServer 10.10.22.22 -emailFromAddr DP-Unity01@dell.com
启用后 ConnectEMC，如果对其进行测试，则会成功通过： 
09:05:02 root@CKM002XXXXX929 spb:/cores/service/user# uemcli -u admin -securepassword /sys/support/connecthome test
Password:
Storage system address: 127.0.0.1
Storage system port: 443
HTTPS connection

Remote certificate:
Issuer:   CN=DP-UNITY01
Subject:  CN=DP-UNITY01
Valid from: 2020:06:14:07:13:27
Valid to:  2023:06:14:07:13:27
Serial:   00a382cb17422be9fd
Id:     2957123456
Would you like to:
 [1] Accept the certificate for this session
 [2] Reject the certificate
Please input your selection (The default selection is [1]):
Operation completed successfully.
  1. 列出 配置更改后的当前详细信息：
uemcli /sys/support/connecthome show -detail

Please input your selection (The default selection is [1]):
1:  Enabled       = yes
   SMTP server     = 10.1XX.1XX.1X1
   E-mail from address = DP-Unity01@dell.com
   E-mail to address  = emailalert@emc.com

Additional Information

请参阅 Dell Unity 系列 Unisphere 命令行界面用户指南作为参考。 

Affected Products

Dell EMC Unity Family
Article Properties
Article Number: 000224165
Article Type: Solution
Last Modified: 18 Dec 2025
Version:  4
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.