NVP vProxy: How to manually clone a VM save set from a non-Data Domain device to a Data Domain clone device

Resumen: This article goes over the steps required to manually clone a VMware Virtual Machine (VM) save set from a non-Data Domain device to a Data Domain device.

Este artículo se aplica a Este artículo no se aplica a Este artículo no está vinculado a ningún producto específico. No se identifican todas las versiones del producto en este artículo.
Consulte estos recursos

Instrucciones

In order to recover Virtual Machine (VM) data that was backed up through the NetWorker VMware Protection (NVP) vProxy appliance, the data must reside on a Data Domain device. The typical restore process can resurrect (clone) the data from a non-Data Domain device to a Data Domain. This KB provides an overview of how to manually clone VM save sets back to a Data Domain disk device.

 

  1. If a Data Domain Clone device is not available, create a Data Domain Clone device from the "Devices" tab "Device creation wizard." The device should use the NetWorker server as a storage node (not a standalone NetWorker storage node host "remote"). Select the "Backup Clone" option and select an existing Clone Pool or Create a New One. For the KB example, a new pool "VMstaging" is created:
Creating a Data Domain clone pool device
  1. From the NetWorker server, open an Admin/root command prompt and run the following command to get the SSID/cloneid of the alternate source save set:  
mminfo -avot -q vmname=VM_NAME -r "savetime,ssid,cloneid,volume(40),pool,type"
NOTE: Replace VM_NAME with the name of the VM as it appears in VMware for the VM you want to perform the recover action for. 
[root@nsr ~]# mminfo -avot -q vmname=win-client01.amer.lan -r "savetime,ssid,cloneid,volume(40),pool,type"
  date   ssid          clone id volume                                 pool           type
...
10/17/2024 4128316607 1729438570 ddvectVMclone.002                      ddvect_VMclone DD Cloud Tier
  1. Clone the save set to the Data Domain clone pool:  
nsrclone -b "Clone_Pool_Name" -S SSID/CloneID -y "MM/DD/YYYY"

 

NOTE: Replace Clone_Pool_Name with the Data Domain clone pool name from step 1, and SSID/CloneID with the alternate source save set’s SSID/Clone ID from step 2. -y "MM/DD/YYYY" is optional. This can be used to set the retention time you want the clone copy to reside in the VMstaging pool. If nsrclone runs without a specified retention time, the new save set clone’s retention defaults to the maximum clone retention of the existing save set clones.

Example: 
[root@nsr ~]# nsrclone -b VMstaging -S 4128316607/1729438570 -y "10/30/2024"
180169:nsrclone: Step (1 of 16): NSRCLONE_INIT_PHASE_ONE: nsrclone has been started on host 'nsr.amer.lan', with command 'nsrclone -b VMstaging -S 4128316607/1729438570 -y 10/30/2024 '.
...
...
180196:nsrclone: Step (14 of 16): NSRCLONE_TERMINATE_PHASE_THREE: Clone operation is exiting with job_exit_status=0 (before): jobid=672023, args.exit_status=0.
         RPS CLONE RESULTS
         [ORIGINAL REQUESTED SAVESETS]
4128316607/1729438570;
         [CLONE SUCCESS SAVESETS]
4128316607/1729439658;
  1. Verify the save set is listed under the staging pool:
mminfo -avot -q vmname=VM_NAME -r "savetime,ssid,cloneid,volume(40),pool,type"
Example: 
[root@nsr ~]# mminfo -avot -q vmname=win-client01.amer.lan -r "savetime,ssid,cloneid,volume(40),pool,type"
  date   ssid          clone id volume                                 pool           type
10/17/2024 4128316607 1729438570 ddvectVMclone.002                      ddvect_VMclone DD Cloud Tier
10/17/2024 4128316607 1729439658 VMstaging.002                          VMstaging      Data Domain
  1. Once the save set is cloned to a local Data Domain device, the cloned save set it is listed under "Recover the virtual machine from a clone on a Data Domain device" in the "Recover Source" window.
Recovering save set from DD clone

Información adicional

NVP vProxy: VM Recovery fails from clone copy on Tape.


For more info and options for the mminfo and nsrclone commands, see the NetWorker Command Reference Guide for your NetWorker version, available at: https://www.dell.com/support/home/product-support/product/networker/docs 
 

Productos afectados

NetWorker

Productos

NetWorker
Propiedades del artículo
Número del artículo: 000157773
Tipo de artículo: How To
Última modificación: 23 sept 2025
Versión:  7
Encuentre respuestas a sus preguntas de otros usuarios de Dell
Servicios de soporte
Compruebe si el dispositivo está cubierto por los servicios de soporte.