Passer au contenu principal
Quitter

Bienvenue dans l’univers Dell

Mon compte
  • Passer des commandes rapidement et facilement
  • Afficher les commandes et suivre l’état de votre expédition
  • Créez et accédez à une liste de vos produits
  • Gérer vos sites, vos produits et vos contacts au niveau des produits Dell EMC à l’aide de la rubrique Gestion des informations de l’entreprise.
Se connecter Créer un compte Connexion au compte Premier Connexion au programme de partenariat
Nous contacter

Vos paniers Dell.com

Numéro d’article: 000121440

How to configure MAC based port security on Dell N2000, N3000, and N4000 series switches.

Résumé: Dell EMC Networking N-Series configuring MAC based port security on switches.

Cet article a peut-être été traduit automatiquement. Si vous avez des commentaires concernant sa qualité, veuillez nous en informer en utilisant le formulaire au bas de cette page.

Contenu de l’article

Instructions

Article Summary: This article shows how to configure MAC based port security on Dell N Series switches



Table of Contents
 

 
  1. How to enable MAC based port security on the N Series Switch
  2. How to statically add MAC address to an Interface
  3. How to configure a maximum amount of allowed MAC addresses
  4. How to configure the maximum limit of dynamically learned mac addresses on a specific interface
 

How to enable MAC based port security on the N series switch

   
Command Parameters
console>enable Enter enable Privilege Exec mode.
console#config Enter configuration mode.
console(config)#switchport port-security Enable port security globally on the switch.  
console(config)#interface gi1/0/5 Enter specific interface that needs port security.
console(config-if-gi1/0/5)#switchport port-security Enable port security on the interface level.
   
 
HOW10392_en_US__1icon Note: When port security is enabled on an interface, all dynamic MAC addresses learned on that port are removed, and the port re-learns any MAC addresses on that interface.
 


How to statically add MAC addresses to an interface

   

 

Command Parameters
console#config Enter configuration mode.
console(config)# mac address-table static c2f3.220a.12f4 vlan 1 interface gi1/0/5 This adds the MAC address c2f3.220a.12f4 to the MAC table for interface gi1/0/5.
console(config)#no mac address-table static c2f3.220a.12f4 vlan 1 interface gi1/0/5 Add "no" to the beginning of the command to remove the MAC address.

 

How to configure a maximum amount of allowed Static MAC addresses

   
Command Parameters
console#config Enter configuration mode.
console(config)#interface gi1/0/5 Enter specific interface that needs port security.
console(config-if-Gi1/0/5)#switchport port-security maximum 3 Sets the max limit of static MAC addresses to 3.  Range is <0-100>  Default is 100.
   
 
HOW10392_en_US__1icon Note: To clear dynamically learned MAC addresses from a port, you must perform the following example command.
console#clear mac address-table dynamic interface gi1/0/5
   
 
HOW10392_en_US__1icon Note: By default when port security violations occur, the port discards any frames on that interface originating from violating MAC addresses. The port is not shut down.  If you are wanting the port to actually shut down you will need to add this command to the specific interfaces that require that feature:  
(config-if-Gi1/0/5)#switchport port-security violation shutdown : 
   
 


How to configure the maximum limit of dynamically learned mac addresses on a specific interface

 

 
Command Parameters
console#config Enter configuration mode.
console(config)#interface gi1/0/5 Enter specific interface that needs port security.
console(config-if-gi1/0/5)#switchport port-security dynamic 0 This example uses 0 as you would normally want the port not to learn macs dynamically.  Range is <0-600>   Default is 100.

 

 

Propriétés de l’article

Produit concerné

PowerSwitch N2000 Series, PowerSwitch N3000 Series, PowerSwitch N4000 Series

Dernière date de publication

21 févr. 2021

Version

3

Type d’article

How To

Haut de la page