VPLEX: How to reduce Java's high CPU utilization on the management server.

Samenvatting: This article walks through the process of lowering the Java's high CPU utilization percentage. This can be done by restarting the management console.

Dit artikel is van toepassing op Dit artikel is niet van toepassing op Dit artikel is niet gebonden aan een specifiek product. Niet alle productversies worden in dit artikel vermeld.

Symptomen

Restart the Management Station console from the management server using the command;
sudo /etc/init.d/VPlexManagementConsole restart

Checking the VPLEX management server Java utilization shows that it is consuming over 100%.

service@#########:~> top
top - 14:45:38 up 993 days, 3:16, 4 users, load average: 1.37, 1.43, 1.47
Tasks: 137 total, 2 running, 135 sleeping, 0 stopped, 0 zombie
Cpu(s): 50.9%us, 0.3%sy, 0.0%ni, 48.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st
Mem: 3920420k total, 3361876k used, 558544k free, 26616k buffers
Swap: 8388604k total, 3750660k used, 4637944k free, 350828k cached

PID   USER     PR NI VIRT  RES  SHR  S %CPU %MEM TIME+    COMMAND
11316 service  25 5  6902m 2.7g 9868 S 101  71.4 47236:56 java

Oorzaak

This can be seen in environments that have been up for extended periods of time. In these situations, the services running on the management server can start to consume too many resources.

Oplossing

Before restarting any management console or management server, ensure that there are no ongoing migrations (device or extent)

Run the below commands on the Management Station console:

Step 1: Verify the management server console's pid:

Example:
service@#########:~> sudo /etc/init.d/VPlexManagementConsole status
VPlexManagementConsole is running (pid 11315)


Step 2: Restarting of management server console: (to restart the Management Server software.)

Example:
service@#########:~> sudo /etc/init.d/VPlexManagementConsole restart
Restarting EMC VPlex Management Console... done


Step 3: Post restarting the management server software verify the pid:

Example:
service@#########:~> sudo /etc/init.d/VPlexManagementConsole status
VPlexManagementConsole is running (pid 23533)



Check if the issue is resolved after the restart.

service@#########:~> top
top -      15:05:08 up 993 days, 3:36, 5 users, load average: 1.72, 1.57, 1.52
Tasks:     144 total,     2 running,         142 sleeping,       0 stopped,     0 zombie
Cpu(s):    36.8%us,       2.0%sy, 0.0%ni, 45.3%id, 15.7%wa, 0.0%hi, 0.2%si, 0.0%st
Mem:       3920420k       total,     1446552k       used, 2473868k free, 27192k buffers
Swap:      8388604k       total,     81112k         used, 8307492k free, 484428k cached


PID   USER     PR  NI  VIRT  RES  SHR  S %CPU %MEM  TIME+    COMMAND
23534    service            20       0        2840m      1.2g     23m    S     6         33.0     22:57.52          java

Getroffen producten

VPLEX Series

Producten

VPLEX for All Flash, VPLEX GeoSynchrony, VPLEX Series, VPLEX VS2, VPLEX VS6
Artikeleigenschappen
Artikelnummer: 000029009
Artikeltype: Solution
Laatst aangepast: 09 jan. 2026
Versie:  4
Vind antwoorden op uw vragen via andere Dell gebruikers
Support Services
Controleer of uw apparaat wordt gedekt door Support Services.