Ana içeriğe atla
Oturumu Kapat

Dell'e Hoş Geldiniz

Hesabım
  • Hızla ve kolayca sipariş verin
  • Siparişleri görüntüleyin ve kargonuzun durumunu izleyin
  • Ürünlerinizin listesini oluşturun ve listeye erişin
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.
Oturum Aç Hesap oluşturun Premier Oturum Açma İş Ortağı Programı Oturum Açma
Bize Ulaşın

Article Number: 000144060

Latitude 5591 Teardown removal guide for customer replaceable units (CRUs)

Summary: This article is a guide to those parts of the Dell Latitude 5591 notebook that considers it OK for anyone to remove and replace.

Article Content

Symptoms

These guides will take you step by step through the safe removal of what are considered to be the Customer Replaceable Unit (CRU) parts of a Latitude 5591 Notebook system. (CRUs are the parts of the system that shouldn't need an engineer to remove or replace.) The guides will also include pictures to reference what's involved.

Table of Contents:

  1. CRU Removal Guide
  2. Removal Instructions

 

Removal Guide

 

If these guides do not cover what you are looking to do, then you will want to reference your System Manual.

The article below provides information on safe practises to take into consideration before working with electrical equipment.


Back to Top

 

Removal Instructions

 

SLN311213_en_US__1icon Note: Please click on the title of the section you want to open below, in order to see the contents.
 
|

 

SLN311213_en_US__2ReqTools_E7450_BKeith_01

1 Small Phillip's head screwdriver 2 Plastic Scribe
3 Small Flat head screwdriver    
 
SLN311213_en_US__1icon Note: Be aware that using a large Phillips or Flat Head screwdriver may result in damage to the head of the screws. This would make their removal impossible without speciality tools, that aren't available to our onsite engineers.

 

  1. Pre-Removal Instructions Before removing the Main Access Panel:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

  2. Loosen the eight (8) captive screws that secure the cover to the chassis [1]

SLN311213_en_US__45591_Cover_BK_1

  1. Using a plastic scribe or similar tool, pry the base cover up from the top edge of the system and then continue around the cover to release it from the chassis. [2]

  2. Lift the cover up and off the chassis.

SLN311213_en_US__55591_Cover_BK_2

 

  1. Pre-Removal Instructions Before removing the Battery:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the System Cover

  2. Disconnect the battery cable from the motherboard and remove the cable from the routing channel. [1]

  3. Loosen the captive screw on the side of the battery closest to the right hand side of the chassis. [2]

SLN311213_en_US__65591_Battery_BK

  1. Lift the Battery up and out of the system [3].

SLN311213_en_US__1icon Note: Touch systems ship with a 68Whr battery and Non-Touch systems ship with a 51Whr battery.

 

  1. Pre-Removal Instructions Before removing the Keyboard Trim:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the System Cover and Battery

  2. Using a plastic scribe or similar tool, pry up the trim starting at the access points [1], and continue around the trim going in a clockwise direction. Lift up from the right hand side [2] to remove from the system.

SLN311213_en_US__85591_Keyboard_BK_1

 

  1. Pre-Removal Instructions Before removing the Keyboard:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the System Cover, Battery and Keyboard Trim

  2. Lift the latch and remove the keyboard cable from the connector [1].

  3. Lift the latch and remove the other keyboard cables from the connectors [2,3,4].

SLN311213_en_US__95591_Keyboard_BK_2

SLN311213_en_US__1icon Note: The number of keyboard cables depends on the type of keyboard you ordered.

  1. Turn the system back onto its base and open the system up. Remove the five (5) screws that secure the keyboard to the chassis [1].

  2. Using a plastic scribe, pry the keyboard up from the bottom and lift it up out of the system [2].

SLN311213_en_US__115591_Keyboard_BK_3

  1. Be careful removing the keyboard from the system as you will need to pull the keyboard cables through from the rear of the system.

SLN311213_en_US__125591_Keyboard_BK_4

 

  1. Pre-Removal Instructions Before removing the Memory:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the System Cover and Battery

  2. Pull the metal clips on the short sides of the memory dimm apart, until the module pops up at an angle to the connector [1].

  3. Lift the memory dimm out of the system [2].

SLN311213_en_US__135591_Memory_BK

SLN311213_en_US__1icon Note : Please repeat Steps 2 and 3 for any additional Memory DIMMs located in the system.

 

  1. Pre-Removal Instructions Before removing the Solid State Drive (SSD):

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the System Cover and Battery

  2. Peel off the adhesive mylar shield from on top of the SSD [1].

SLN311213_en_US__1icon Note: For models shipped with NVMe SSD's, remove the thermal plate placed over the SSD.

  1. Remove the screw that secures the end of the SSD to the motherboard [2], lift the card to a 35 degree angle and remove from the connector [3].

SLN311213_en_US__165591_SSD_BK_1

SLN311213_en_US__1icon Note: For Non-Touch systems, peel off the adhesive tape that is placed above the SSD card and remove the screw.

  1. Once the card is removed you can remove the SSD frame by removing the securing screw that holds it to the system [1].

SLN311213_en_US__185591_SSD_BK_2

  1. Lift the frame out of the system [2].

 

  1. Pre-Removal Instructions Before removing the Hard Disk Drive (HDD):

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the System Cover and Battery

  2. Disconnect the HDD cable from the connector on the motherboard [1], and remove the four (4) screws that secure the HDD to the chassis [2].

  3. Lift the drive out of the system [3].

SLN311213_en_US__195591_HDD_BK

SLN311213_en_US__1icon Note: This system default ships with SSD, shipping with an HDD is optional.

 

  1. Pre-Removal Instructions Before removing the Coin Cell Battery:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the System Cover and Battery

  2. Disconnect the coin cell battery cable from the connector on the motherboard [1] and lift the coin cell battery up and away from the adhesive holding it to the motherboard [2].

SLN311213_en_US__215591_Coin_BK

 

  1. Pre-Removal Instructions Before removing the WLAN Card (WiFi, Wireless):

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the System Cover and Battery

  2. Remove the screw that secures the card to the system [1], remove the bracket that secures the antenna cables [2] and disconnect the antenna cables from the WLAN card [3].

SLN311213_en_US__225591_WLAN_BK

SLN311213_en_US__1icon Note: When removing the wireless card from the system, make sure the adhesive pad under the card stays on the system board/chassis frame during the removal process.

  1. Lift the card out of the connector and the system [4].

 

  1. Pre-Removal Instructions Before removing the WWAN CARD (3G, Cellular):

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the System Cover and Battery

  2. Remove the screw that secures the card to the system [1], remove the bracket that secures the antenna cables [2] and disconnect the antenna cables from the WWAN card [3].

SLN311213_en_US__245591_WWAN_BK

  1. Lift the card out of the connector and the system [4].

 

  1. Pre-Removal Instructions Before removing the Hinge Covers:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the System Cover and Battery

  2. You need to remove the screw from each hinge cover [1] and then pull the cover up and away from the system [2].

SLN311213_en_US__255591_Hinge_BK

 

  1. Pre-Removal Instructions Before removing the SD Memory Card:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

  2. You have to push in on the SD card in order for it to pop out of the system of the system [1], once it pops out - you can grip it and pull it all of the way out of the system [2].

 

  1. Pre-Removal Instructions Before removing the SIM Card:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

  2. Insert a straightened paper clip or the SIM card removal tool into the pinhole on the SIM card tray [1].

  3. Pull on the SIM card tray when it pops out of the side of the system [2].

SLN311213_en_US__265591_SIM_BK

  1. Remove the SIM card from the tray and push the empty tray into the slot until it clicks in place.

 

If you require further assistance, please contact Technical Support

 

  Contact Us  

Article Properties

Affected Product

Latitude 5591

Last Published Date

10 Nis 2021

Version

4

Article Type

Solution

Üste Dön