Chassis Management Controller Version 5.1 for Dell PowerEdge M1000e RACADM Command Line Reference Guide

racadm ?

racadm ? <subcommand>

Example for RACADM?

The following output example shows the actual output for the RACADM? command. Descriptions shown in this example may vary slightly from the descriptions in your RACADM session.

racadm ?

 help            -- list racadm subcommand description
                                 help <subcommand> -- display usage summary for a subcommand
                                 ?               -- list racadm subcommand description
                                 ? <subcommand>  -- display usage summary for a subcommand
                                 arp             -- display the networking arp table
                                 chassisaction   -- execute power-up/down/cycle or reset operation
                                 chassislog      -- display the chassislog
                                 closessn        -- close a session
                                 clrraclog       -- clear the CMC log
                                 clrsel          -- clear the System Event Log (SEL)
                                 cmcchangeover   -- changes the redundant state of the CMC from active to standby and vice versa
                                 config          -- modify CMC configuration properties
                                 connect         -- connect to switch or blade serial console
                                 deploy          -- deploy blade or IOM by specifying required properties
                                 feature         -- display features active on the chassis / feature deactivation
                                 featurecard     -- feature card status and list the available features
                                 fwupdate        -- update the firmware on a CMC, server, IOM inf or KVM
                                 get             -- save CMC configuration properties to a file
                                 getactiveerrors -- display CMC active errors
                                 getassettag     -- display asset tag
                                 getchassisname  -- get the chassisname
                                 getconfig       -- display CMC configuration properties
                                 getdcinfo       -- display general I/O module and DC configuration information
                                 getfanreqinfo   -- display fan request information for Servers and Switches
                                 getflexaddr     -- display Flexaddress enablement status for all slots and fabrics.
                                 getioinfo       -- display general IO information and stack information
                                 getkvminfo      -- display the KVM module information
                                 getled          -- display the LED settings on a module
                                 getmacaddress   -- get MAC/WWN addresses
                                 getmodinfo      -- get module configuration and status information
                                 getniccfg       -- display network settings for modules
                                 getpbinfo       -- get power budget status information
                                 getpminfo       -- get power management status information
                                 getraclog       -- display the CMC log
                                 getractime      -- display the current CMC time
                                 getredundancymode -- gets the redundancy mode of the CMC
                                 getsel          -- display records from the System Event Log (SEL)
                                 getsensorinfo   -- display system sensors
                                 getslotname     -- gets the name of the slot in the chassis
                                 getssninfo      -- display session information
                                 getsvctag       -- display service tag information
                                 getsysinfo      -- display general CMC and system information
                                 gettracelog     -- display the CMC diagnostic trace log
                                 getversion      -- display version information for modules
                                 getarraycfg     -- display's storage array properties
                                 ifconfig        -- display network interface information
                                 jobqueue        -- Jobqueue of the jobs currently scheduled
                                 krbkeytabupload -- upload an Kerberos Keytab to the CMC
                                 netstat         -- display routing table and network statistics
                                 ping            -- send ICMP echo packets on the network
                                 ping6           -- send ICMP echo packets on the network
                                 racdump         -- display CMC diagnostic information
                                 racreset        -- perform a CMC or RAC reset operation
                                 racresetcfg     -- restore the CMC configuration to factory defaults
                                 remoteimage     -- connect, disconnect or deploy a media file on a remote server
                                 serveraction    -- perform system power management operations
                                 set             -- import saved CMC configuration from a file
                                 setassettag     -- set the asset tag for the specified module
                                 setchassisname  -- sets the name of the chassis
                                 setflexaddr     -- enable/disable the Flexaddress feature on a per fabric, per slot basis.
                                 setled          -- set state of the LEDs on a module
                                 setniccfg       -- modify network configuration properties
                                 setractime      -- set the time on the CMC
                                 setslotname     -- sets the name of the slot in the chassis
                                 setsysinfo      -- set the chassis name and chassis location
                                 setarraycfg     -- configure's storage array properties
                                 sshpkauth       -- manage PK Authentication keys and accounts
                                 sslcertdownload -- download an SSL certificate from the CMC
                                 sslcertupload   -- upload an SSL certificate to the CMC
                                 sslcertview     -- display a CA/server certificate in the CMC
                                 sslcsrgen       -- generate a certificate CSR from the CMC
                                 sslresetcfg     -- generate a new self-signed certificate
                                 testemail       -- test CMC e-mail notifications
                                 testfeature     -- test CMC feature x
                                 testtrap        -- test CMC SNMP trap notifications
                                 traceroute      -- determine the route of a packet
                                 traceroute6     -- determine the route of a packet
                                 wsman           -- perform wsman client functions for servers.
                                 
                              

Example for RACADM? <subcommand>

racadm ? getsysinfo

getsysinfo -- display general CMC and system information
                                 Usage:
                                 racadm getsysinfo [-d] [-c] [-A] [-4] [-6]
                                 -----------------------------------------------------------
                                 Valid Options:
                                 -d : show CMC information
                                 -c : show chassis information
                                 -A : do not show headers or labels
                                 -4 : show CMC IPv4 information
                                 -6 : show CMC IPv6 information