- Notes, cautions, and warnings
- Additional Resources
- Introduction
- Import requirements and restrictions
- General requirements for importing data
- Dell EqualLogic PS Series specific requirements
- Dell Compellent SC Series specific requirements
- Dell Unity specific requirements
- Dell VNX2 Series specific requirements
- Dell XtremIO XI and X2 specific requirements
- Dell PowerMax and VMAX3 specific requirements
- NetApp AFF and A Series specific requirements
- General block-based import restrictions
- General file-based import restrictions
- Host plugin installation (block-based non-disruptive import only)
- Installing the host plugin for import on a Windows-based host
- Installing the host plugin for import on a Linux-based host
- Installing the Dell EqualLogic MEM kit on an ESXi-based host
- Install the Dell EqualLogic MEM kit on an ESXi-based host using the vSphere CLI
- Install the Dell EqualLogic MEM kit on an ESXi-based host using setup.pl script on VMA
- Install the Dell EqualLogic MEM kit on an ESXi-based host using VUM
- Install the Dell EqualLogic MEM kit during an ESXi-based host upgrade
- Uninstalling the host plugin for import
- Import workflows
- Non-disruptive import workflow
- Cutover workflow for non-disruptive import
- Cancel workflow for non-disruptive import
- Agentless import workflow
- Cutover workflow for agentless import
- Cancel workflow for agentless import
- File-based import workflow
- Cutover workflow for file-based import
- Cancel workflow for file-based import
- Configuring and managing import
- Configure a non-disruptive import
- Refresh hosts and volumes in a non-disruptive import
- Manage non-disruptive import sessions
- Configure an agentless import
- Manage agentless import sessions
- Configure a File Mobility Network for file-based import
- Configure the connection to a remote system for file-based import
- Configure file import interface
- Configure a file-based import
- Manage file-based import sessions
- Import-CLI (Linux)
- Additional tasks related to import for Linux-based hosts
- ImportKit-CLI (Windows)
- How to run the ImportKit CLI commands
- List supported arrays
- Host plugin log information
- Import kit version
- Restart import kit host plugin service
- Import volumes information
- Get Web server port information
- Install import kit certificate
- Re-generate the import kit certificate
- Set Web server port information
- Set host plugin logging debug log level
- Import-CLI (VMware)
- CLI for EQL MPIO
- Fault handling by PowerStore import
Dell PowerStore Importing External Storage to PowerStore Guide
Revert SATP, VAAI, and PSP to default settings
NOTE:Import-CLI command for EQL HIT Kit package. This command is applicable to the Dell EqualLogic Peer Storage (PS) series and should only be run before the volume is selected for Import.
Reverts the SATP, VAAI, and PSP of Dell EqualLogic PS volumes claimed by DellEMC SATP (DellEMC_IMPORT_SATP, T10 Identification VAAI, and VMW_PSP_RR) to VMW_SATP_EQL, VMW_VAAIP_EQL, and DELL_PSP_EQL_ROUTED, respectively.
Format
esxcli import {changeToDefault [-d <NAAID_of_source>]}Options
| Options | Descriptions |
|---|---|
| -d <NAAID_of_source> | Specifies the NAA ID of the source volume. |
Example
# esxcli import changeToDefault -d naa.64ed2a75493a4a1b5abb45508ae779c6 SATP,VAAI and PSP VAAI set to VMW_SATP_EQL,VMW_VAAIP_EQL,DELL_PSP_EQL_ROUTED respectively Reboot the host to apply the set claimrules
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\