Passer au contenu principal
Quitter

Bienvenue dans l’univers Dell

Mon compte
  • Passer des commandes rapidement et facilement
  • Afficher les commandes et suivre l’état de votre expédition
  • Créez et accédez à une liste de vos produits
  • Gérer vos sites, vos produits et vos contacts au niveau des produits Dell EMC à l’aide de la rubrique Gestion des informations de l’entreprise.
Se connecter Créer un compte Connexion au compte Premier Connexion au programme de partenariat
Nous contacter

Dell PowerEdge FN I/O Module Configuration Guide 9.10(0.0)

PDF

Configuring the Control VLAN

Control and member VLANS are configured normally for Layer 2. Their status as control or member is determined at the FRRP group commands.

For more information about configuring VLANS in Layer 2 mode, refer to Layer 2.
Be sure to follow these guidelines:
  • All VLANS must be in Layer 2 mode.
  • You can only add ring nodes to the VLAN.
  • A control VLAN can belong to one FRRP group only.
  • Tag control VLAN ports.
  • All ports on the ring must use the same VLAN ID for the control VLAN.
  • You cannot configure a VLAN as both a control VLAN and member VLAN on the same ring.
  • Only two interfaces can be members of a control VLAN (the Master Primary and Secondary ports).
  • Member VLANs across multiple rings are not supported in Master nodes.

To create the control VLAN for this FRRP group, use the following commands on the switch that is to act as the Master node.

  1. Create a VLAN with this ID number. CONFIGURATION mode. interface vlan vlan-id VLAN ID: from 1 to 4094.
  2. Tag the specified interface or range of interfaces to this VLAN. CONFIG-INT-VLAN mode. tagged interface slot/ port { range}
    • For a 10/100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
    • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
    • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
    Slot/Port, Range : Slot and Port ID for the interface. Range is entered Slot/Port-Port.
  3. Assign the Primary and Secondary ports and the control VLAN for the ports on the ring. CONFIG-FRRP mode. interface primary int slot/port secondary int slot/port control-vlan vlan id
    • For a 10/100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
    • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
    • For a SONET interface, enter the keyword sonet then the slot/port information.
    • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
    Slot/Port, Range : Slot and Port ID for the interface. Range is entered Slot/Port-Port. VLAN ID : The VLAN identification of the control VLAN.
  4. Configure the Master node. CONFIG-FRRP mode. mode master
  5. Identify the Member VLANs for this FRRP group. CONFIG-FRRP mode. member-vlan vlan-id { range} VLAN-ID, Range : VLAN IDs for the ring’s member VLANS.
  6. Enable FRRP. CONFIG-FRRP mode. no disable

Évaluez ce contenu

Précis
Utile
Facile à comprendre
Avez-vous trouvé cet article utile ?
0/3000 characters
  Veuillez attribuer une note (1 à 5 étoiles).
  Veuillez attribuer une note (1 à 5 étoiles).
  Veuillez attribuer une note (1 à 5 étoiles).
  Veuillez indiquer si l’article a été utile ou non.
  Les commentaires ne doivent pas contenir les caractères spéciaux : <>()\