- Notes, cautions, and warnings
- Dell PowerEdge FC630 overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- Viewing System BIOS
- System BIOS Settings details
- Boot Settings
- Network Settings
- System Security
- System Information
- Memory Settings
- Processor Settings
- SATA Settings
- Integrated Devices
- Serial Communication
- System Profile Settings
- Miscellaneous Settings
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing sled components
- Safety instructions
- Recommended tools
- Sled
- Inside the sled
- Cooling shroud
- Processor blank and DIMM blank
- System memory
- PCIe mezzanine card
- Internal dual SD module (optional)
- rSPI card (optional)
- SD vFlash card
- Network Daughter Card
- Processors
- Hard drives or SSDs
- Hard drive or SSD bay numbering
- Hard drive or SSD installation guidelines
- Removing a hard drive or SSD
- Installing a hard drive or SSD
- Removing a hard drive or SSD blank
- Installing a hard drive or SSD blank
- Shutdown procedure for servicing a hard drive or SSD
- Configuring the boot drive
- Removing a 2.5-inch hard drive or SSD from a 2.5-inch hard drive or SSD carrier
- Installing a 2.5-inch hard drive or SSD in a 2.5-inch hard drive or SSD carrier
- Removing a 1.8-inch SSD from a 1.8-inch SSD carrier
- Installing a 1.8-inch SSD in a 1.8-inch SSD carrier
- Removing the hard drive or SSD cage
- Installing the hard drive or SSD cage
- Hard drive backplane
- PERC H730P slim card
- Storage controller card
- NVRAM backup battery
- System board
- Trusted Platform Module
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Getting help
Bienvenue
Bienvenue dans l’univers Dell
Mon compte
- Passer des commandes rapidement et facilement
- Afficher les commandes et suivre l’état de votre expédition
- Créez et accédez à une liste de vos produits
- Gérer vos sites, vos produits et vos contacts au niveau des produits Dell EMC à l’aide de la rubrique Gestion des informations de l’entreprise.
Dell PowerEdge FC630 Owner's Manual
System Security Settings details
The System Security Settings screen details are explained
as follows:
- Option
- Description
- Intel AES-NI
- Improves the speed of applications by performing encryption and decryption by using the Advanced Encryption Standard Instruction Set (AES-NI). This option is set to Enabled by default.
- System Password
- Sets the system password. This option is set to Enabled by default and is read-only if the password jumper is not installed in the system.
- Setup Password
- Sets the setup password. This option is read-only if the password jumper is not installed in the system.
- Password Status
- Locks the system password. This option is set to Unlocked by default.
- TPM Security
- NOTE: The TPM menu is available only when the TPM module is installed.Enables you to control the reporting mode of the TPM. The TPM Security option is set to Off by default. You can only modify the TPM Status, TPM Activation, and Intel TXT fields if the TPM Status field is set to either On with Pre-boot Measurements or On without Pre-boot Measurements.
- TPM Information
- Changes the operational state of the TPM. This option is set to No Change by default.
- TPM Status
- Specifies the TPM status.
- TPM Command
- CAUTION: Clearing the TPM results in the loss of all keys in the TPM. The loss of TPM keys may affect booting to the operating system.Clears all the contents of the TPM. The TPM Clear option is set to No by default.
- Intel TXT
- Enables or disables the Intel Trusted Execution Technology (TXT) option. To enable the Intel TXT option, virtualization technology and TPM Security must be enabled with Pre-boot measurements. This option is set to Off by default.
- Power Button
- Enables or disables the power button on the front of the system. This option is set to Enabled by default.
- AC Power Recovery
- Sets how the system behaves after AC power is restored to the system. This option is set to Last by default.
- Secure Boot
- Enables Secure Boot, where the BIOS authenticates each pre-boot image by using the certificates in the Secure Boot Policy. Secure Boot is disabled by default.
- Secure Boot Policy
- When Secure Boot policy is set to Standard, the BIOS uses the system manufacturer’s key and certificates to authenticate pre-boot images. When Secure Boot policy is set to Custom, the BIOS uses the user-defined key and certificates. Secure Boot policy is set to Standard by default.
- Secure Boot Policy Summary
- Specifies the list of certificates and hashes that secure boot uses to authenticate images.
Veuillez attribuer une note (1 à 5 étoiles).
Veuillez attribuer une note (1 à 5 étoiles).
Veuillez attribuer une note (1 à 5 étoiles).
Veuillez indiquer si l’article a été utile ou non.
Les commentaires ne doivent pas contenir les caractères spéciaux : <>()\