OEMR R340

This article provides information about how to verify if a Network Interface Card (NIC) is compatible with a PowerEdge Server.

This article provides information about CPU Machine Check errors and common causes and proper handling when errors are seen.

Unsure about the procedure to update a specific component's firmware in a PowerEdge system? Learn how to in this specific article.

R7725, R6725, R7715, and R6715 the number of CPU Cores is not recognized correctly.

Dell Technologies advises against downgrading Hard Drive or SSD firmware, except in validated scenarios, due to unpredictable results and version reporting issues.

After a system restart, the Integrated Dell Remote Access Controller (iDRAC) may not display the Virtual Disk information intermittently.

PowerEdge servers crash with PCIe fatal errors while updating Kioxia CM6 NVMe drive firmware.

CPUs can be perceived to be hot while server is idle.

The Dell SS540 SAS solid state drive is reported as not correctly functioning.

PowerEdge servers with Emulex Fiber Channel (FC) driver version 12.01.12 may fail driver installation under Windows Defender Application Control (WDAC) Enforced Mode on Windows Server.

PowerEdge: Broadcom NXE devices with Driver 229.2.73 (SWB: Y7T4X) may report that the interfaces are missing in the operating system when secure boot is enabled.

This article presents opportunities to understand and troubleshoot some common causes of fan noise in a PowerEdge server. It is also relevant for 100% fan speeds.

This article describes how to view and clear the system event log (SEL) in System Setup.

This article describes how to find the iDRAC's current MAC address.

Dell solid state drive (SSD) fails after system reports low environment operating temperature.

Dell Samsung Serial Attached SCSI (SAS) PM1653 and PM1655 solid state drives may report excessive Sense Key faults 0x3, 0x11, 0x0, or 0x4, 0x29, 0x4. These faults have the potential to cause unexpected drive issues.

Dell Enterprise SAS, SATA SSD: SMART predictive failures triggered by remaining write endurance falling below the threshold

In some migration scenarios, the OpenManage Enterprise 4.0 target import operation may fail with an error 'Failed to decrypt backup archive' during migration. Use the following article to help in troubleshooting this scenario and various ways to address the failure.

Network port enumeration on Windows Server 2022 with Dell network adapters may swap port designations.

After an update to 7.00.00.00 or higher, the iDRAC9 web server may become inaccessible where the user has uploaded a custom or CA signed web certificate.

The iDRAC is unable to connect to a Server Message Block (SMB) share when the optional "SMB3 share encryption" is enabled.

BIOS/CPLD or backplane firmware DUP may fail to update when attempted soon after iDRAC restart.

This article describes what can happen while collecting SupportAssist logs using iDRAC9 UI. The operation may result in an error, or incomplete logs may be collected.

BIOS, CPLD, Backplane, PSU, or few other firmware update on Red Hat Enterprise Linux (RHEL) 9 may report failure when update attempted using Dell Update Package (DUP).

This article addresses an issue in which conversion of Windows Server from an evaluation to a fully licensed edition fails. The error that is returned appears to indicate a problem with the supplied product key, but the key is known to be valid.

The firmware of PowerEdge server hard drives is a critical component in the server system. Regularly updating and maintaining this firmware is essential for server performance, security, and compatibility. Hard drive firmware updates can often fix known hardware faults and issues, address identified vulnerabilities and security problems, and potentially introduce new features, improvements, and enhancements.

PowerEdge RAID Controller (PERC11, PERC10), Human Interface Infrastructure (HII) configuration utility, and iDRAC do not support array expansion.

This how-to explains the commands and shows the results of outputs for the same to retrieve your service tag using a command console. It is displayed as the system serial number.

The VM does not turn on after configuring PCI Device passthrough on the ESXi host and adding the device to the VM. It gets stuck at 80% and then results in an error "total number of pages needed (4206594) exceeds the limit (917504)."

This article provides information about an EasyRestore Identity Module (IDM) failure and being unable to install the IDM manually.