Removal
BOSS N1 card carrier
Identify the BOSS N1 card carrier highlighted in blue.
Pull and lift the BOSS N1 card carrier retention latch lock to open.
Slide the BOSS N1 card carrier out.
System Cover
Identify the system cover highlighted in blue.
Using a flat head or a Phillips screwdriver, rotate the lock counterclockwise to the unlock position.
Lift the release latch until the system cover slides back.
Lift the cover from the system.
BOSS Module
Identify the BOSS module highlighted in blue.
Disconnect the BOSS N1 power cable and signal cable from the BOSS module.
Remove the screw that secures the BOSS N1 module on Riser 1.
Slide the BOSS N1 module towards the front of the chassis and lift the module.
Airshroud
Riser 1B
Identify the riser 1B highlighted in blue
Loosen the captive screws on the riser.
Press the blue button on the riser, and holding the touch points lift the expansion card riser 1B from the riser connector on the system board.
Riser 3B
Identify the riser 3B highlighted in blue
Loosen the captive screw on the riser.
Press the blue button on the riser, and holding the touch points lift the expansion card riser 3B from the riser connector on the system board.
Riser 4B
Identify the riser 4B highlighted in blue
Loosen the captive screw on the riser.
Press the blue button on the riser, and holding the touch points lift the expansion card riser 4B from the riser connector on the system board.
Intrusion switch
Identify the intrusion switch module highlighted in blue.
Disconnect the intrusion switch cable from the connector on the rear I/O board.
Loosen the screw that secures the intrusion switch on the intrusion switch slot.
Lift to remove the intrusion switch out of the intrusion switch slot.
Install
Intrusion switch
Identify the intrusion switch module highlighted in blue.
Align and insert the intrusion switch in the slot until it is firmly seated in the slot on the system.
Tighten the screw that secures the intrusion switch on the intrusion switch slot.
Connect the intrusion switch cable to the connector on the rear I/O board.
Riser 4B
Identify the riser 4B location highlighted in blue
Holding the edges or the touch points, align the holes on the expansion card riser 4B with the guides on the system board.
Lower the expansion card riser 04 into place and press the touch points until the expansion card riser connector is fully seated on the system board connector.
Tighten the captive screw on the riser.
Riser 3B
Identify the riser 3B location highlighted in blue
Holding the edges or the touch points, align the holes on the expansion card riser 3B with the guides on the system board.
Lower the expansion card riser 3B into place and press the touch points until the expansion card riser connector is fully seated on the system board connector.
Tighten the captive screw on the riser.
Riser 1B
Identify the riser 1B location highlighted in blue
Holding the edges or the touch points, align the holes on the expansion card riser 1B with the guides on the system board.
Lower the expansion card riser 1B into place and press the touch points until the expansion card riser connector is fully seated on the system board connector.
Tighten the captive screws on the riser.
Airshroud
BOSS Module
Identify the BOSS module location highlighted in blue.
Insert the BOSS N1 controller card module and push the module towards the rear of the system until it is secured.
Install the screw to secures the BOSS N1 module on Riser 1.
Connect the BOSS power and signal cable to the connectors to the BOSS module.
System Cover
Identify the system cover location highlighted in blue.
Align the tabs on the system cover with the guide slots on the system and slide the system cover.
Close the system cover release latch.
Using a flat head or Phillips screwdriver, rotate the lock clockwise to the lock position.
BOSS N1 card carrier
Identify the BOSS N1 card carrier location highlighted in blue.
Slide the BOSS N1 card carrier into the BOSS N1 module slot.
Close the BOSS N1 card carrier release latch to lock the carrier in place.