Removal
System Cover
Identify the system cover highlighted in blue.
Using a flat head or a Phillips screwdriver, rotate the lock counter clockwise.
Lift the latch till the system cover slides back.
Hold the cover on both sides, and lift the cover away from the system.
Butterfly riser
Identify the butterfly riser assembly highlighted in blue
Loosen the captive screw that secures the riser to the system
Hold the touch points, and lift the expansion card riser, from the riser connector, on the system board.
Air shroud
Identify the air shroud highlighted in blue
Holding the touch points, lift the cooling shroud away from the system.
Expansion Card
Select the expansion card you want to replace .
Pull and lift up the expansion card retention latch lock to open.
Hold the expansion card by the edge and pull the card to disconnect from the system board connector.
Internal PERC riser
Identify the internal PERC riser highlighted in blue.
Open the cable guiding latch for easy access.
Lower the plunger.
Hold the blue touch points and lift the internal PERC riser out of the system.
Turn the internal riser so that the PERC card is facing up.
Press the cable connector and disconnect the cable connected to the internal PERC card.
Internal Dual SD Module (IDSDM)
Identify the internal dual SD module (IDSDM) highlighted in blue
Pull up on the blue pull tab and lift the IDSDM out of the system
PHM
System memory
Select the system memory you want to replace
To release the memory module from the socket, simultaneously press the ejectors on both ends of the socket.
Lift and remove the memory module from the system.
LOM riser card
Identify the LOM riser card highlighted in blue
Loosen the screws that secure the LOM riser card to the system board.
Release the two blue side plastic snaps holding the LOM riser card.
Hold the LOM riser card by the edges on either side, and lift to remove it from the connector on the system board.
Slide the LOM riser card towards the front of the system until the Ethernet connectors or the Small form-factor pluggable (SFP) are clear of the slot in the back of the system.
System Battery (Coin Cell)
Identify the system battery highlighted in blue
Use a plastic scribe to pry out the system battery.
Lift the battery out of the socket.
System Board
Identify the system board highlighted in blue
Lift the cable latch and disconnect the control panel cable from the connector on the system board.
Disconnect the cables from the system board.
Disconnect the cables from the system board.
Remove screws securing the system board to the chassis.
Slide it toward the front of the chassis and Incline the system board at an angle and lift the system board out of the system.
Install
System Board
Identify the system board location highlighted in blue
Lower the system board into the chassis at an angle and push the system board toward the back of the chassis until the board clicks into place.
Install the screws to secure the system board to the chassis.
Connect the cables to the system board
Connect the cables to the system board
Connect the cable to the system board connector and secure it using cable latch
System Battery (Coin Cell)
Identify the system battery location highlighted in blue
Install the battery with the "+" facing up and slide it under the securing tabs.
Press the battery into the connector until it snaps into place.
LOM riser card
Identify the LOM riser card location on the system board.
Align the connectors on the LOM riser card with the slot on the system.
Press the LOM riser card until the card is firmly seated on the system board connector and the two blue plastic snap hold the LOM riser card in place.
Using a Phillips #2 screwdriver, replace the screws to secure the LOM riser card to the system board.
System memory
Confirm the system memory you want to replace.
Align the edge connector of memory module with the alignment key of the memory module socket, and insert into the socket.
Press the memory module until the socket levers firmly click into place.
PHM
Internal Dual SD Module (IDSDM)
Identify the internal dual SD module (IDSDM) location highlighted in blue
Align the IDSDM connector with the connector on the system board
Press the IDSDM into the connector
Internal PERC riser
Identify the internal PERC riser location highlighted in blue.
Connect the cable to the internal PERC card.
Holding the blue touch points, align the slot on the internal PERC riser to the guide on the system board.
Insert the internal riser card’s edge connector firmly into the system board connector until the riser is fully seated.
Lift the plunger to lock the riser in place.
Close the cable guiding latch.
Expansion Card
Confirm the expansion card you want to replace
Press the expansion card firmly into the expansion card connector on the system board until the card is fully seated.
Push the expansion card latch
Air shroud
Identify the cooling shroud location highlighted in blue
Align the tabs on the air shroud with the slots on the system.
Lower the air shroud into the system until it is firmly seated.
StepInfoTxt
Butterfly riser
Identify the butterfly riser assembly location highlighted in blue
Lower the expansion card riser into place until the expansion card riser connector is fully seated in the connector.
Tighten the captive screw that secures the riser to the system
System Cover
Identify the system cover location highlighted in blue.
Align the tabs on the system cover with the guide slots on the system.
Push the system cover latch down.
Using a flat head or Phillips screwdriver, rotate the lock clockwise.
StepInfoTxt