Removal
BOSS S2 - card carrier
Identify the BOSS S2 card carrier highlighted in blue.
Pull and lift the BOSS S2 card carrier retention latch lock to open.
Slide the BOSS S2 card carrier out.
System Cover
Identify the system cover highlighted in blue.
Using a 1/4 inch flat head or a phillips #2 screwdriver rotate the lock counterclockwise to the unlock position.
Lift the release latch until the system cover slides back.
Lift the cover from the system.
BOSS S2 module
Identify the BOSS S2 module highlighted in blue.
Disconnect the BOSS S2 power and signal cable from the BOSS S2 module.
Using the phillips #1 screwdriver remove the screw that secures the BOSS S2 module on Riser 1.
Slide the BOSS S2 module towards the front of the chassis and lift the module.
Air Shroud
Identify the air shroud highlighted in blue.
Hold the edges of the air shroud, and lift the air shroud out of the system.
Riser - 1C
Identify the riser highlighted in blue.
Loosen the captive screws on the riser and system.
Press the blue release tab on the riser and holding the edges lift the expansion card riser from the riser connector on the system board.
Riser - 3A
Identify the riser highlighted in blue.
Loosen the captive screw on the system.
Press the blue release tab on the riser and holding the edges lift the expansion card riser from the riser connector on the system board.
Riser - 3A Expansion Card
Position the riser so that the expansion card will be visible to remove.
Identify the expansion card highlighted in blue.
Pull and rotate the expansion card retention latch lock to open.
Pull the card holder before removing the card from the riser.
Hold the expansion card by the edges and pull the card from the riser.
Install
Riser - 3A Expansion Card
Identify the expansion card location highlighted in blue.
Pull and lift up the expansion card retention latch lock to open.
Insert the card firmly into the expansion card connector until seated.
Close the expansion card retention latch.
Push the card holder to hold the card in the riser.
Position the riser to install into the system.
Riser - 3A
Identify the riser location highlighted in blue.
Holding the edges or the touch points, align the holes on the expansion card riser with the guides on the system board.
Lower the expansion card riser into place and press the touch points until the expansion card riser connector is fully seated on the system board connector.
Tighten the captive screw on the system.
Riser - 1C
Identify the riser location highlighted in blue.
Holding the edges or the touch points, align the holes on the expansion card riser with the guides on the system board.
Lower the expansion card riser into place and press the touch points until the expansion card riser connector is fully seated on the system board connector.
Tighten the captive screws on the risers and system.
Air Shroud
Identify the air shroud location highlighted in blue.
Align the slot on the air shroud with the standoff on the system.
Lower the air shroud into the system until it is firmly seated.
BOSS S2 module
Identify the BOSS S2 module location highlighted in blue.
Align the BOSS S2 module at an angle with the controller card module slot.
Insert the BOSS S2 module and push the module horizontally towards the rear of the system until firmly seated.
Using the phillips #1 screwdriver, install the screw that secures the BOSS S2 module to the system.
Connect the BOSS S2 power and signal cable to the connectors on the BOSS S2 module.
System Cover
Identify the system cover location highlighted in blue.
Align the tabs on the system cover with the guide slots on the system and slide the system cover.
Close the system cover release latch.
Using a 1/4 inch flat head or phillips #2 screwdriver, rotate the lock clockwise to the lock position.
BOSS S2 - card carrier
Identify the BOSS S2 card carrier location highlighted in blue.
Slide the BOSS S2 card carrier into the BOSS S2 module slot.
Close the BOSS S2 card carrier release latch to lock the carrier in place.