Removal
Power Supply Units
Select the power supply unit (PSU) you want to replace
Disconnect the power cable from the PSU
Press the orange release latch and slide the PSU out of the system by using the PSU handle
System Cover
Identify the system cover highlighted in blue.
Using a 1/4" Flathead or a Phillips #2 screwdriver, rotate the lock counter clockwise.
Lift the latch untill the system cover slides back.
Hold the cover on both sides, and lift the cover away from the system.
Cooling fan cage assembly
Identify the cooling fan cage assembly highlighted in blue
Lift the blue release levers to unlock the cooling fan cage assembly from the system
Hold the release levers, and lift the cooling fan cage assembly from the system.
Air Shroud
Identify the air shroud highlighted in blue
Holding the edges of the air shroud, incline the air shroud at an angle.
Move the cables away from the air shroud to prevent the cables from being pinched or crimped.
Lift the air shroud from the system.
PSU Cage
Identify the PSU cage highlighted in blue
Disconnect the cables from the connectors on the power distribution board.
Disconnect the cables from the connectors on the power distribution board.
Using both hands slowly rotate and pull up the PSU cage handle.
Hold the handle with one hand and the rear of the PSU cage to lift away from the system
System Memory
Select the system memory you want to replace. System can have up to 24 dimms installed.
To release the memory module from the socket, simultaneously press the ejectors on both ends of the socket.
Holding the memory by the edges, lift to remove.
PHM
Boss cage
Identify the system battery highlighted in blue
Use a plastic scribe to pry out the system battery.
Lift the battery out of the socket.
OCP card
Identify the Optional OCP card highlighted in blue
Press the latches on OCP card airshroud to remove it from the system.
Open the blue latch to disengage the OCP card.
Slide the OCP card out of the slot on the system.
LOM card
Identify the LOM card highlighted in blue
Remove the screws that secure the LOM card to the system board.
Holding the edges, pull the LOM card to disconnect from the connector on the system board.
Rear IO card
Identify the Rear IO card highlighted in blue
Remove the screws that secure the Rear IO card to the system board.
Holding the edges, pull the Rear IO card to disconnect from the connector on the system board.
System Board
Identify the system board highlighted in blue
Disconnect and unroute the cable from the system board.
Disconnect the cables from the system board.
Disconnect the cables from the system board.
Disconnect the cables from the system board.
Open the side wall bracket latches and unroute the cables from side wall brackets.
Remove the side wall brackets from the system.
Disconnect the left & right control panel cables from the system board.
Unroute the left & right control panel cables from the system board.
Using the system board holder and plunger, slide the system board towards the front of the system.
At a tilted angle, lift the system board out of the chassis.
Install
System Board
Identify the system board location highlighted in blue
Hold the blue plastic handle and sheet metal handle on the system board and place it onto the chassis.
Hold onto the blue plastic handle with one hand and use the other hand to push the plunger, sliding the system board towards the rear of the chassis until it clicks and locks plunger.
Route the left & right control panel cables to the system board.
Connect the left & right control panel cables to the system board.
Install the side wall brackets to the system.
Route the cables to the side wall brackets and close the side wall bracket latches.
Connect the cables to the system board.
Connect the cables to the system board.
Connect the cables to the system board.
Route and connect the cable to the system board.
Rear IO card
Identify the Rear IO card location on the system board.
Align the connectors and slots on Rear IO card with the connector and standoffs on the system board.
Press the Rear IO card until firmly seated on the system board connector.
Using a Phillips #2 screwdriver, secure the Rear IO card to the system board with the two screws.
LOM card
Identify the LOM card location on the system board.
Align the connectors and slots on LOM card with the connector and standoffs on the system board.
Press the LOM card until firmly seated on the system board connector.
Using a Phillips #2 screwdriver, secure the LOM card to the system board with the two screws.
OCP card
Identify the Optional OCP card highlighted in blue
Slide the OCP card into the slot in the system.
Close the blue latch to lock the OCP card to the system.
Install the airshroud on OCP card.
Boss cage
Identify the BOSS cage location highlighted in blue.
Align and place the BOSS cage on the system.
Slide the BOSS cage toward the front of the system until it clicks into place to lock from key slot.
Connect the intrusion switch cable to the connector on the rear I/O board and Connect the BOSS-N1 power and signal cables to the connectors on the BOSS-N1 module.
PHM
System Memory
Confirm the highlighted memory DIMM is the correct location to install or change selection.
Align the edge connector of memory module with the alignment key of the memory module socket, and insert into the socket.
Press the memory module until the socket levers firmly click into place.
PSU Cage
Identify the PSU cage location highlighted in blue
Using both hands slowly rotate and pull up the PSU cage handle.
Hold the handle with one hand and the rear side of PSU cage, align and insert the PSU cage with the help of guiding slots at both sides of the chassis.
Rotate the handle down to lock position.
Connect the cables to the connectors on the power distribution board.
Connect the cables to the connectors on the power distribution board.
Air Shroud
Identify the air shroud location highlighted in blue
Tilt the air shroud at an angle and align the air shroud tabs with the system slots.
Lower the air shroud into the system until it clicks into place.
Cooling fan cage assembly
Identify the cooling fan cage assembly location highlighted in blue
Holding the blue release lever of the cooling fan cage, align the guide rails on the cooling fan cage assembly with the standoffs on the system.
Lower the cooling fan cage assembly into the system until the cooling fan cage connectors engage with the connectors on the system board.
Lower the blue release lever and press to lock the cooling fan cage assembly into the system.
System Cover
Identify the system cover location highlighted in blue.
Align the tabs on the system cover with the guide slots on the system.
Push the system cover latch down.
Using a 1/4" Flathead or a Phillips #2 screwdriver, rotate the lock clockwise.
Power Supply Units
Confirm the highlighted PSU is the correct location to install or change selection.
Slide the PSU into the system until the PSU is fully seated and the release latch snaps into place
Connect the power cable to the PSU