Removal
Front Bezel
Identify the front bezel highlighted in blue
Unlock the front bezel by using the key.
Press the release button and disengage the left end of the bezel.
Unhook the right end, and remove the front bezel.
System Cover
Identify the system cover highlighted in blue.
Using a flat head or a Phillips screwdriver, rotate the lock counter clockwise.
Lift the latch until the system cover slides back.
Hold the cover on both sides, and lift the cover away from the system.
Riser 1A
Identify the riser 1A highlighted in blue
Using a Phillips screwdriver, loosen the blue thumb screw on the riser.
Disconnect any cables that are connected to the expansion card or the riser.
Pull the plunger and slide to the unlock position (slide to the rear of the chassis).
Lift the expansion card riser from the riser connector on the system board.
Riser 4A
Identify the riser 4A highlighted in blue
Using a Phillips screwdriver, loosen the blue thumb screw on the riser.
Disconnect any cables that are connected to the expansion card or the riser.
Pull the plunger and slide to the unlock position (slide to the rear of the chassis)
Lift the expansion card riser from the riser connector on the system board.
Storage tray
Identify the storage tray highlighted in blue
Disconnect the cables from the system board connectors.
Disconnect the intrusion switch and fan board cables from the connector.
Using a Phillips screwdriver, remove the screws on the drive cage.
Lift the handle and slide the storage tray towards the front of the system.
Lift the storage tray out of the system.
Lower brace cover
Identify the lower brace cover highlighted in blue
Using two fingers press the touch point on the lower brace cover to release it from the lower brace.
Processor and Direct Liquid Cooling module
Identify the heatsink highlighted in blue
Using the two fingers, lift the turtle shell from the DLC module.
Remove the liquid cooling hoses with numbers naming 11 an 12.
Release the blue thumb holder and rotate the metallic gate away from the liquid cooling tray.
Disconnect the cooling module, right control panel and intrusion cable from the connectors on the system board assembly.
Unroute the right control panel and intrusion cables from the cooling module.
Loosen the first and second screws three turns.
Loosen the third and fourth screws completely.
Loosen the captive screws 1 and 2 completely.
Loosen the captive screws 3 and 4 completely.
Set the anti-tilt wires on the DLC module to the unlock position and lift the DLC module from the system.
Place the heat sink on a flat surface with the processor side facing up
Processor
Place the DLC module with the processor side facing up.
Identify the processor highlighted in blue
Using your thumb, lift the thermal interface material (TIM) break lever to release the processor from the TIM and retaining
clip.
Holding the processor by the edges, lift the processor away from the retaining clip.
Using your thumb and index finger, first hold the retaining clip release tab at the pin 1 connector, pull out the tip of the clip release tab, and then lift the retaining clip partially.
After all the corners are released from the DLC module, lift the retaining clip from the pin 1 corner of the DLC module.
Remove the thermal grease on the heat sink by using a clean lint-free cloth.
Install
Processor
Place the DLC module with the processor side facing up.
Identify the process location highlighted in blue
Align the retaining clip with the processor.
Place the retaining clip on top of the processor in the processor tray aligning pin 1 indicator on the processor.
Align the processor with retaining clip, by using your fingers press the retaining clip on all the four sides until it clicks into place.
Use the thermal grease syringe included with your kit to apply the grease in a thin spiral on the bottom of the heat sink or For new heat sink, remove the Thermal Interface Material (TIM) protective film from the base of heat sink.
Place the processor assembly on the DLC module and press the base of the DLC until the retaining clip locks at all the four corners.
Place the DLC module with the processor side facing downwards.
Processor and Direct Liquid Cooling module
Identify the heatsink assembly Location highlighted in blue
Align the DLC module with the standoff screws on the system board.
Place the module on the processor slot and set all the anti-tilt wires to locked position (outward position).
Partially tighten the first and second screws (approximately 3 turns).
Partially tighten the third and fourth screws (approximately 3 turns).
Tighten the captive screws 1 and 2 completely.
Tighten the captive screws 3 and 4 completely.
Route the right control panel and intrusion cables to the cooling module.
Connect the cooling module, right control panel and intrusion cable to the connectors on the system board assembly.
Reconnect the liquid cooling hoses 11 an 12 to Manifold from DLC module.
Rotate the metallic gate near to the liquid cooling tray and lock the blue thumb holder.
Using the two finger, align and install the turtle shell on the DLC module.
Lower brace cover
Identify the lower brace cover location highlighted in blue
Align the lower brace cover on the lower brace along the arrow, using two fingers press the touch point on the lower brace cover until it firmly seated on the lower brace.
Storage tray
Identify the storage tray location highlighted in blue
Align and insert the storage tray on the guiding slots of the chassis.
Press down the handle and slide the tray into the chassis toward the rear of the system until it is firmly seated.
Using a Phillips screwdriver, install the screws to secure on the drive cage.
Connect the cables in to the system board connectors.
Connect the intrusion switch and fan board cables to the connector.
Riser 4A
Identify the riser 4A location highlighted in blue
Holding the blue touch points, align the holes on the expansion card riser with the guides on the system board.
Lower the expansion card riser into place and press the touch points until the expansion card riser connector is fully seated on the system board connector.
Pull the plunger and slide to the lock position (slide to the front of the chassis).
Using a Phillips screwdriver, tighten the blue thumb screw to secure the riser on the chassis.
Connect the cables to the expansion card or the riser.
Riser 1A
Identify the riser 1A location highlighted in blue
Holding the blue touch points, align the holes on the expansion card riser with the guides on the system board.
Lower the expansion card riser into place and press the touch points until the expansion card riser connector is fully seated on the system board connector.
Pull the plunger and slide to the lock position (slide to the front of the chassis).
Using a Phillips screwdriver, tighten the blue thumb screw to secure the riser on the chassis.
Connect the cables to the expansion card or the riser.
System Cover
Identify the system cover location highlighted in blue.
Align the tabs on the system cover with the guide slots on the system and slide the system cover.
Close the system cover release latch.
Using a flat head or Phillips screwdriver, rotate the lock clockwise to the lock position.
Front Bezel
Identify the front bezel location highlighted in blue
Align and insert the tabs on the bezel into the slots on the system.
Press the bezel until the release button clicks in place.
Lock the front bezel by using the key.