AUTOMATISKT INSTALLERADDen här filen installerades automatiskt som en del av en ny uppdatering. Om du har problem kan du ladda ner och installera om den manuellt.
Innehållet på den här sidan kan ha översatts automatiskt. Fyll i formuläret längst ned på sidan för att ge feedback.
Den här filen installerades automatiskt som en del av en ny uppdatering. Om du har problem kan du ladda ner och installera om den manuellt.
This software contains the Windows NT4 driver for the DELL PERC 2, PERC 2/Si, PERC 3/Si, and PERC 3/Di controllers.
Rekommenderat
Hitta den bästa nerladdningen för ditt system
Ange din produktinformation för att se den senaste informationen om drivrutiner för ditt system
Sök efter support
Ange din Dell service tag eller modell
Vill du söka efter din produkt? Ange en produktidentifierare.Visa mig hur
Inga resultat hittades. Vi kunde inte hitta något som matchade din sökning. Ändra din sökning och försök igen.
Den här drivrutinen är inte kompatibel
Den här drivrutinen gäller inte för den valda produkten. Välj en annan produkt för att ange din produktinformation för den här drivrutinen igen eller gå till produktsupportsidan för att visa alla drivrutiner för en annan produkt.
Logga in på Windows som administratör för att använda automatisk skanning. Om du redan är inloggad som administratör och ser det här meddelandet ska du starta om.Ditt system hanteras av IT-administratören och funktionerna kan vara begränsade.
Hitta fler uppdateringar. Använd SupportAssist för att hitta alla de senaste drivrutinsuppdateringarna för din enhet.
Korrigeringar och förbättringar
Fixes/Enhancements ==================
-Filter driver checks Dispatch_Level before calling KeWaitForSingleObject avoid bugcheck 0xB8 -Modified unknown AIF handling to prevent Driver Verifier hang. -STATUS_INVALID_PARAMETER returned for requests with: Zero-length input buffer size.Invalid input buffer size, i.e. not the size of the expected structure. Invalid memory address for the input buffer.A null input buffer. -Deletes perc2hib reference in lower filter list rather than entire filter list via inf. -Corrected a major entry-point in the filter driver that Windows uses for major Plug-N-Play requests (IRP_MJ_PNP). This entry point was incorrectly passing the request to the next lower device in the device stack. -Deleted the section that removes the upper and lower filters. This section caused errors to be logged in the setupapi.log in Windows. -Added support for new vSCSI implementation
Dell Technologies rekommenderar att du installerar den här uppdateringen under nästa schemalagda uppdateringscykel. Uppdateringen innehåller ändringar för att bibehålla det allmänna systemtillståndet. Den säkerställer att systemets programvara förblir aktuell och kompatibel med andra systemmoduler (fast programvara, BIOS, drivrutiner och programvara) och kan inkludera andra nya funktioner.
This software code release requires all V2.8 components: firmware, device driver and management utilities. Using some components from previous releases may cause some unknown errors.
Driver Installation for Windows NT 4.0 ==============================================
To perform a fresh installation of the Windows NT device drivers for the controller, follow these steps:
1. Boot the system using the Windows NT 4.0 CD.
2. When the message: "Setup is inspecting your computer's hardware configuration" appears, press F6 immediately.
3. The Windows NT 4.0 Setup screen will appear, requesting input for additional adapters in the system. Press 'S' to specify an additional adapter.
4. A selection menu will appear. Scroll to "Other" and hit ENTER.
5. Insert the driver diskette and press ENTER when prompted.
6. The selection: "DELL PERC 2, 2/Si, 3/Si, 3/Di RAID CONTROLLERS" will appear, hit ENTER.
7. After the driver has loaded, press ENTER to continue the installation.
NOTE: Before you perform the upgrade, uninstall the Controller Management Software (FAST and the CLI). See the installation guide associated with your controller for instructions on how to uninstall the Controller Management Software.
To upgrade the Windows NT device drivers for the controller, follow these steps: 1. Follow this path from Start:
3. The system displays an "Install Driver" window. Select "Have Disk".
4. The system displays an "Install From Disk" window. The "Install Driver" window instructs you to insert the manufacturer's installation media into the drive and click < Ok>. In this case, insert the diskette that contains the NT device drivers for your controller
5. Enter the drive and location of the files. The default location on the diskette that contains the NT device drivers is: "a:\".
The system displays a message identifying the controller for which you want to upgrade the Windows NT device drivers. The message requests that you click the button.
6. The system displays "System Settings Change" and asks if you want to restart the computer. Press YES.