Ga naar hoofdinhoud
Uitloggen

Welkom bij Dell

Mijn account
  • Snel en eenvoudig bestellen
  • Bestellingen en de verzendstatus bekijken
  • Een lijst met producten maken en openen
  • Beheer uw Dell EMC locaties, producten en contactpersonen op productniveau met Company Administration.
Inloggen Een account maken Inloggen bij Premier Aanmelden voor partnerprogramma
Contact

Uw Dell.com-winkelwagentjes

Dell OpenManage Server Administrator Version 7.3 Command Line Interface Guide

PDF

Omconfig Controller Commands

The following table provides the omconfig command syntax required to execute controller tasks.
  • CAUTION: The omconfig storage controller action=resetconfig controller=id resets the controller configuration. Resetting the controller configuration permanently destroys all data on all virtual disks attached to the controller. System or boot partition residing on these virtual disks is destroyed.
Table 1. Omconfig Controller Commands
Required Command Levels (1, 2, 3) Optional name=value pairs
omconfig storage controller action=rescan controller=id
  action=enablealarm controller=id
  action=disablealarm controller=id
  action=quietalarm controller=id
  action=testalarm controller=id
  action=resetconfig controller=id [force=yes]
 
action=createvdisk controller=id raid=<c | r0 | r1| r1c | r5 | r6 | r10 | r50 | r60> size=<number | b | m | g | max | min> pdisk=<PDISKID> [stripesize=< 2kb | 4kb | 8kb | 16kb | 32kb | 64kb | 128kb | 256kb | 512kb | 1mb >] [cachepolicy=<d | c>] [readpolicy=<ra | nra | ara | rc | nrc>] [writepolicy=<wb | wt | wc | nwc | fwb>] [diskcachepolicy=<disabled | enabled>] [name=<string>] [spanlength=<n>] | [secureflag=yes]
  • NOTE: For RAID 10 on SAS controllers with firmware version 6.1 and later, spanlength is an optional parameter (default=2).
  action=setrebuildrate controller=id rate=<0 to 100>
  action=setchangecontrollerproperties controller=<id> [bgirate=<rate>][reconstructrate=<rate>][checkconsistencyrate=<rate>][rebuildrate=<rate>][clearredundantpath=clear][abortcheckconsistencyonerror=<enabled/disabled>][loadbalance=<auto/disabled>][allowrevertibilehotspareandreplacemember=enabled/disabled] [autoreplacememberonpredictivefailure=<enabled/disabled>][persistenthotspare=enabled/disabled]rate=<0 to 100>
  action=discardpreservedcache controller=id force=<enabled/disabled>
 
action=createsecuritykey controller=id keyid=<keyid> passphrase=<passphrase string> [escrow=yes] [filepath=<Absolute path to the escrow file>]
  • NOTE: If you set escrow=yes, specify the escrow file path.
 
action=changesecuritykey controller=id keyid=<keyid> passphrase=<passphrase string> oldpassphrase=<oldpassphrase string> [escrow=yes] [filepath=<Absolute path to the escrow file>]
  • NOTE: If you set escrow=yes, specify the escrow file path.
  action=deletesecuritykey controller=id
  action=setbgirate controller=id rate=<0 to 100 >
  action=setreconstructrate controller=id rate=<0 to 100>
  action=setcheckconsistencyrate controller=id rate=<0 to 100>
  action=exportlog controller=id
  action=importsecureforeignconfig controller=id passphrase=<passphrase for imported foreign configuration>
  action=importforeignconfig controller=id
  action=importrecoverforeignconfig controller=id
  action=clearforeignconfig controller=id
 
action=setpdiskpwrmanagement controller=id spindownunconfigureddrives=<enabled/disabled> spindownhotspares=<enabled/disabled> spindownconfigureddrives=<enabled/disabled> idlec=<enabled/disabled> spindowntimeinterval=<30 to 1440>(minutes) spinupstarttime=<HH:MM:AM/PM> spinuptimeinterval=<1 to 24>(hours)
  • NOTE: Specify spinupstarttime and spinuptimeinterval only when you set spindownconfigureddrives=enabled.
  action=setpatrolreadmode controller=id mode=<manual | auto | disable>
  action=startpatrolread controller=id
  action=stoppatrolread controller=id
  action=createcachecade controller=id pdisk=<PDISKID> [name=<string>]
 
action=enablelkm controller=id keyid=<keyid> passphrase=<passphrase string> [escrow=yes] [filepath=<Absolute path to the escrow file>]
  • NOTE: If you set escrow=yes, specify the escrow file path.
 
action=switchtolkm controller=id keyid=<keyid> passphrase=<passphrase string> [escrow=yes] [filepath=<Absolute path to the escrow file>]
  • NOTE: If you set escrow=yes, specify the escrow file path.
  action=rekeylkm controller=id
  action=convertraidtononraid controller=id pdisk=<PDISKID>
  action=convertnonraidtoraid controller=id pdisk=<PDISKID>

Beoordeel deze inhoud

Nauwkeurig
Nuttig
Eenvoudig te begrijpen
Was dit artikel nuttig?
0/3000 characters
  Geef een beoordeling (1-5 sterren).
  Geef een beoordeling (1-5 sterren).
  Geef een beoordeling (1-5 sterren).
  Selecteer of het artikel nuttig is of niet.
  Opmerkingen mogen geen speciale tekens bevatten: <>() \